{"product_id":"dji-agras-t100-t70p-t55-avionics-sealing-ring-kit-5-pcs-replacement-quarterly-program","title":"DJI Agras T100 – T70P – T55 Avionics Sealing Ring Kit (5 Pcs)","description":"\u003cp\u003e\u003cstrong\u003eDJI Agras Avionics Sealing Ring Kit | Electronics Compartment Environmental Seals | Genuine DJI OEM 5-Piece Kit | Quarterly Replacement Program\u003cbr\u003e\u003cbr\u003eBilled quarterly at the price shown above\u003c\/strong\u003e\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🇺🇸 U.S.A. FIRST\u003c\/h2\u003e\n\u003cp\u003eAres Acres LLC is a U.S.-based authorized DJI Agras reseller supporting American agricultural drone operators with genuine DJI Agras OEM replacement parts, accessories, and field-ready inventory.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFREE \u0026amp; FAST Shipping is included for all U.S. customers, every cycle.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe avionics sealing rings are the environmental barrier around the electronics compartment — the gaskets standing between wash-down water, chemical mist, and dust and the flight control boards that fly the aircraft. Gaskets take compression set, harden under chemistry and heat, and lose seal each time the bay is opened for service. Renewing them on a seasonal schedule is what keeps the compartment's waterproofing rating real instead of nominal.\u003c\/p\u003e\n\u003cp\u003eThis program ships one genuine DJI OEM 5-piece avionics sealing ring kit automatically every 3 months. The price shown is a recurring quarterly program fee, not a one-time purchase price. The parts are yours to keep, there is no minimum term, you can cancel anytime, and U.S. shipping is free every cycle.\u003c\/p\u003e\n\u003cp\u003eCompared with buying the kit one-time and reactively — usually after moisture has already found a board — quarterly replacement costs less per kit and keeps fresh seals always within reach.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eEnroll using the purchase option above — cancel anytime\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe use specialized technicians to verify and dispatch the Avionics Sealing Ring Kit Replacement ordered.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eParts like this one are the reason a grounded aircraft is a repair and not a write-off. A single component held in U.S. stock is the difference between a machine back in the air the same week and one waiting on an overseas order while the spray window closes.\u003c\/p\u003e\n\u003cp\u003eThat is why Ares Acres keeps the seals \u0026amp; vent hardware operators actually run out of in stock and shipped fast within the U.S.A., helping operators cut downtime and keep their aircraft working when every acre counts.\u003c\/p\u003e\n\u003cp\u003eFor professional farmers, aerial applicators, and commercial drone operators running the DJI Agras T100 \/ DJI Agras T70P \/ DJI Agras T55, this is the part that keeps a scheduled job on the calendar instead of on hold.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e✅ DJI Agras T100 \/ T70P \/ T55 Compatibility Guarantee\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e🇺🇸 USA Compatibility Guarantee\u003c\/li\u003e\n\u003cli\u003e👍🏻 Satisfaction Guarantee\u003c\/li\u003e\n\u003cli\u003e💵 Money Back Guarantee\u003c\/li\u003e\n\u003cli\u003e📦 Same Day Shipping \u0026amp; Tracking\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch2\u003e📦 Package Includes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e5 × Genuine DJI Agras OEM Avionics Sealing Rings, shipped automatically every 3 months\u003c\/li\u003e\n\u003cli\u003eA fresh gasket kit every cycle — the parts are yours to keep, no return required\u003c\/li\u003e\n\u003cli\u003eRecurring quarterly program fee at the price shown above — not a one-time purchase price\u003c\/li\u003e\n\u003cli\u003eNo minimum term — cancel anytime and future shipments simply stop\u003c\/li\u003e\n\u003cli\u003eFREE \u0026amp; FAST U.S. shipping on every shipment\u003c\/li\u003e\n\u003cli\u003eEnroll using the purchase option above — current pricing is shown there; cancel anytime\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch2\u003e🔧 Component Overview\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eAvionics Sealing Ring Kit\u003c\/strong\u003e is the genuine DJI OEM gasket set for the electronics compartment on the DJI Agras T100, T70P, and T55. It is the environmental sealing that lets an agricultural aircraft live in chemical mist and wash-down water with computers on board.\u003c\/p\u003e\n\u003cp\u003eThe sealing rings serve to:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSeal the avionics bay against water and wash-down\u003c\/li\u003e\n\u003cli\u003eKeep chemical mist off flight control electronics\u003c\/li\u003e\n\u003cli\u003eBlock dust intrusion at compartment joints\u003c\/li\u003e\n\u003cli\u003eMaintain the bay's environmental rating after service\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThroughout commercial duty, the seals are routinely exposed to compression set under constant clamp load, chemical attack from tank-mix drift, heat cycling, and repeated open-close cycles during maintenance. Every bay opening is a seal event — and seals are one-way parts.\u003c\/p\u003e\n\u003cp\u003eA sealed compartment is a system, not a single gasket, and this kit exists because the bay is closed by several separate interfaces rather than one. Each ring in the set has its own seat, its own clamp load, and its own reason for being the shape it is. The compartment is only as watertight as its worst ring, which is why they are supplied and renewed together. Fitting one fresh ring alongside four that have hardened simply moves the leak to whichever one is now the weakest.\u003c\/p\u003e\n\u003cp\u003eUnderstand how a compartment gasket seals and the replacement interval stops looking arbitrary. The ring is squeezed between two faces and holds them apart by exactly as much as it can push back. Over a season it conforms to those two particular faces in that particular clamped position, and it stops pushing. Reuse it after the cover has been off and it now has a memory of a joint that no longer exists, which is why a bay that was dry all year can start letting water in right after a service.\u003c\/p\u003e\n\u003cp\u003eWater does not need a hole to get into an electronics bay. Fly a black airframe on a hot afternoon, the air inside the compartment expands and pushes out past the seals. Park it and wash it down, and as that air cools it contracts and pulls in whatever is against the outside of the aircraft, which on a spray drone is a film of water and tank mix. That is thermal pumping, and it is the mechanism behind almost every case of moisture found in a bay with no visible leak path anywhere.\u003c\/p\u003e\n\u003cp\u003eThe rings you take out will tell you what has been happening if you lay them out in order. A bright polished band around one ring means that joint has been moving under vibration rather than staying clamped. A section squashed flat means normal compression set. A chalky, stiff surface that leaves powder on your fingers is heat and ultraviolet aging. Splits at a tight radius are a ring that was stretched or rolled into place. A ring that has bonded itself to the groove has been chemically attacked and is telling you what the aircraft has been spraying.\u003c\/p\u003e\n\u003cp\u003eThe corrosion inside a bay is a map of how the water got in. Look at which connector, which board edge, or which corner shows staining first, then work back up the aircraft from there to find the path. Water runs downhill and follows the underside of surfaces, so the entry point is usually above and outboard of the damage, not directly over it. Finding that path matters, because new gaskets fitted under a cracked cover or against a distorted flange will let water in again at the same place.\u003c\/p\u003e\n\u003cp\u003eComing apart, work the cover loose evenly rather than prying up one corner, and note the position each ring came from before anything is set down. Going back together, the seats must be clean and dry, the ring must sit in its groove without being stretched or twisted, and the fasteners must be drawn down in a cross pattern in stages so the gasket is squeezed evenly instead of being pinched on one side and left loose on the other. A gasket that is clamped hard at one end and barely touched at the other is not a seal.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e⚙️ Functional Purpose\u003c\/h2\u003e\n\u003cp\u003eThe program helps:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eKeep fresh gaskets on hand for every avionics service\u003c\/li\u003e\n\u003cli\u003eRenew the environmental barrier on a seasonal schedule\u003c\/li\u003e\n\u003cli\u003eProtect flight controllers from moisture and chemical ingress\u003c\/li\u003e\n\u003cli\u003eKeep the wash-down routine safe for the electronics inside\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eDegraded seals may contribute to: moisture inside the avionics bay, corrosion on connectors and boards, intermittent electrical faults after wash-down, and a flight-controller-level repair caused by a gasket-level part.\u003c\/p\u003e\n\u003cp\u003eKeeping the boards dry is only half of what these seals do. The other half is keeping the connectors dry, and connector corrosion is a nastier fault than a flooded board because it never fails cleanly. A corroded pin still conducts most of the time. It gives you a sensor that drops out on one flight in ten, an error that clears when you wiggle the harness, and days of chasing something that reads as a software problem. Almost all of it starts as moisture that a tired gasket let past.\u003c\/p\u003e\n\u003cp\u003eThere is a mechanical job here as well as an environmental one. A gasket in good condition preloads the joint, which keeps the cover and its fasteners under steady tension in an airframe that vibrates constantly. Once the ring has hardened and taken a set, the joint goes slack, the cover chatters at frequency, and the fasteners start to work loose and fret their bosses. Chasing repeatedly loosening cover screws with more torque, rather than with fresh gaskets, is how threads get stripped out of composite.\u003c\/p\u003e\n\u003cp\u003eThe waterproofing rating a manufacturer publishes for a compartment is a statement about the aircraft as it left the factory, with new seals and undistorted faces. It is not a property the airframe keeps for life. Every hour of heat cycling, every tank of chemistry, and every time the bay is opened moves the compartment away from that condition. Renewing the rings is what turns a rating on a specification sheet back into a barrier that actually exists on your aircraft.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e⚠️ Common Replacement Indicators\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThe avionics bay is being opened for any service\u003c\/li\u003e\n\u003cli\u003eVisible flattening, cracking, or hardening on rings\u003c\/li\u003e\n\u003cli\u003eMoisture traces or dust film inside the compartment\u003c\/li\u003e\n\u003cli\u003eElectrical gremlins appearing after wash-down days\u003c\/li\u003e\n\u003cli\u003eA season quarter of daily duty on the current seals\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eElectrical faults that appear the day after a wash-down and clear once the aircraft has sat in the sun. That pattern is close to diagnostic for moisture inside a sealed volume. Water is bridging something, then evaporating. Open the bay while the fault is present rather than after it clears, because a dry bay two days later tells you nothing and you will have thrown away the one piece of evidence you had.\u003c\/p\u003e\n\u003cp\u003eSensor or heading errors that show up after rain or after the aircraft has been left out overnight uncovered, then behave normally on a dry day. Condensation and ingress both track weather, and both point at the compartment barrier rather than at the sensor. Replacing a sensor that is being flooded intermittently produces a new sensor with the same fault a fortnight later, at many times the price of a gasket kit.\u003c\/p\u003e\n\u003cp\u003eWhite or green powder, or a dull crust, on a connector shell or a board edge inside the bay. That is corrosion, and it means water has been in there long enough to react, not just to visit. Clean it, but do not stop at cleaning. Corrosion at a specific location tells you where the water was running, and that is the clue you need to find the ring or the flange that let it in.\u003c\/p\u003e\n\u003cp\u003eA damp, musty, or chemical smell when the cover comes off. Trust it. A sealed compartment that has stayed sealed smells of nothing but warm plastic. A smell means the bay has been holding moisture and probably tank mix for a while, and it is worth a careful look under every board edge and cable tie before the bay is closed back up.\u003c\/p\u003e\n\u003cp\u003eA fine line of silt, dust, or dried residue along one internal edge of the compartment. That is a tide mark. It shows where standing liquid sat and evaporated, and it points straight at both the entry path above it and the low spot where water collects. It also means the bay has been wet more than once, because a single event rarely leaves a clean line.\u003c\/p\u003e\n\u003cp\u003eWater beads on the underside of the cover but the floor of the bay is dry. That is more likely condensation than ingress: warm humid air was sealed in, then the aircraft cooled. It is still a problem, because the air got in from somewhere, but it changes what you look for. Check any vent path for blockage as well as checking the rings, and close the bay on a dry aircraft rather than a wet one.\u003c\/p\u003e\n\u003cp\u003eThe old gasket tears, stretches, or stays stuck in the groove when the cover comes off. A ring that has bonded to its seat has been softened by chemistry or baked hard by heat, and either way it stopped behaving like a spring some time ago. It also means the groove now needs careful cleaning before anything new goes in, because bits of the old ring left behind will hold the new one off its seat.\u003c\/p\u003e\n\u003cp\u003eCover fasteners that keep coming loose no matter how carefully they are torqued. The usual cause is a gasket that no longer preloads the joint, so there is nothing keeping tension on the screw. Before reaching for thread locker, put fresh rings in and see whether the problem disappears. If it does not, look for a distorted cover, a cracked boss, or a fastener that is the wrong length for the hole it is in.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e📐 Specifications\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eComponent Type:\u003c\/strong\u003e Avionics compartment sealing ring kit \/ environmental gaskets\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCompatibility:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDJI Agras T100\u003c\/li\u003e\n\u003cli\u003eDJI Agras T70P\u003c\/li\u003e\n\u003cli\u003eDJI Agras T55\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eProduct Category:\u003c\/strong\u003e Seals \u0026amp; Vent Hardware\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePackage Quantity:\u003c\/strong\u003e 5 sealing rings per quarterly shipment\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation Area:\u003c\/strong\u003e Avionics \/ electronics compartment\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCondition:\u003c\/strong\u003e Brand new genuine DJI OEM parts\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProgram Structure:\u003c\/strong\u003e Recurring quarterly fee at the price shown above, not a one-time purchase price. One 5-piece kit ships automatically every 3 months; no minimum term; cancel anytime; parts are yours to keep; free U.S. shipping every cycle.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensional figures:\u003c\/strong\u003e Section thickness, diameters, and groove dimensions are not published for these rings. Do not attempt to match them out of a generic seal catalogue by measurement. Match them by DJI parts diagram for your airframe and by direct comparison against the rings you removed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKit contents and positions:\u003c\/strong\u003e Five sealing rings per kit. They are not necessarily interchangeable with one another. Lay them out in the order they come off the aircraft and mark which position each one belongs to, because two rings can look identical and differ in section thickness or free diameter enough to matter once clamped.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSealants and adhesives:\u003c\/strong\u003e Do not add silicone sealant, RTV, or gasket goo to a joint that is designed around a moulded ring. It changes the clamp height the joint was designed for, it makes the next service far worse, and cured sealant fragments end up loose inside a compartment full of connectors. If a joint needs sealant to stay dry, something else is wrong with it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCleaning of seats and rings:\u003c\/strong\u003e Mild soap and water on a clean cloth. No abrasive pads, no wire brushes, and no aggressive solvents on the sealing faces. A scratched or hazed seat leaks, and solvent left in a groove attacks the new ring the moment it goes in. Dry the seat completely before fitting.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStorage of spare kits:\u003c\/strong\u003e Leave the rings in their bag until fitting day, stored flat and unstretched, out of sunlight, away from running electric motors, and away from open fuel and solvent. Ozone and ultraviolet age rubber on the shelf, and a kit that has hardened in storage buys you nothing over the set you are removing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInspection before fitting:\u003c\/strong\u003e Run each new ring through clean fingers before it goes into a groove. Feel for moulding flash on the parting line, a nick, a flat spot from packaging, or a twist that will not relax. A defect too small to see is enough to leave a leak path, and finding it now costs seconds while finding it later costs a full teardown.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🧰 Fitment Verification Before You Order\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eConfirm fitment by part number before ordering.\u003c\/strong\u003e Find the code printed on the component you are replacing, or look it up on the DJI Agras parts diagram for your airframe, and compare it against this listing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRevision suffixes are still the same part.\u003c\/strong\u003e DJI labels sometimes carry a trailing revision such as \u003cem\u003e.01\u003c\/em\u003e, \u003cem\u003e.02\u003c\/em\u003e, or \u003cem\u003e.F\u003c\/em\u003e. Those denote a production revision, not a different component. Match the base number and disregard the suffix.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVisually similar is not the same.\u003c\/strong\u003e DJI Agras parts diagrams list components that look nearly identical but sit at different positions, carry different tolerances, or belong to a different airframe generation. Ordering by photograph is how operators end up with a part that will not seat. Order by number.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVerified fitment for this listing:\u003c\/strong\u003e DJI Agras T100 \/ DJI Agras T70P \/ DJI Agras T55. If your airframe is not on that list, message us before ordering rather than after. We would rather answer a question than process a return, and so would you.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNot sure?\u003c\/strong\u003e Send us a photo of the old part and the label, along with your aircraft model and serial. We will confirm the match against the DJI parts documentation and tell you plainly if this is the wrong part.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🛠️ Installation \u0026amp; Handling Notes\u003c\/h2\u003e\n\u003cp\u003eThese are general safe-practice notes for component replacement on DJI Agras airframes. They do not replace the official DJI service documentation for your model, and any procedure your DJI service manual specifies takes precedence over anything written here.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePower down completely and disconnect the flight batteries\u003c\/strong\u003e before removing any panel, connector, or fastener. Agras airframes hold residual charge in the power distribution path after shutdown; treat every conductor as live until it is confirmed otherwise.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePhotograph the assembly before you disturb it.\u003c\/strong\u003e Cable routing, connector orientation, and fastener lengths on Agras airframes are not interchangeable, and the – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement is easier to fit correctly when you can see how the original sat.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTorque to DJI specification.\u003c\/strong\u003e Overtightening into composite and magnesium-alloy structure strips threads and cracks mounts; undertightening lets a component walk loose under rotor vibration. Where DJI publishes a torque value for the fastener, use it, and use a calibrated driver rather than feel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCheck the mating surfaces and seals while you are in there.\u003c\/strong\u003e A component is only as good as what it seats against. Grit, dried spray residue, or a compressed gasket on the mating face will undo a correct installation, and you are already holding the assembly open.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTest before you spray.\u003c\/strong\u003e Power up on the ground, confirm the aircraft reports no new errors, run the relevant system check in DJI Agras Assistant or the remote controller diagnostics, and hover-test in a clear area before returning to a paid job.\u003c\/p\u003e\n\u003cp\u003eIf the work is outside your comfort level, have it done by a DJI-authorized service technician. The part cost is small next to the airframe.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🚜 Necessary For\u003c\/h2\u003e\n\u003cp\u003eThis program is ideal for: DJI Agras T100, T70P, and T55 operators; fleet maintenance managers; agricultural drone technicians; commercial spraying contractors; and professional operators running scheduled avionics maintenance. Especially valuable during peak-season wash-down routines and pre-season service.\u003c\/p\u003e\n\u003cp\u003eEvery single opening of the avionics compartment, regardless of why it was opened. The gaskets are consumed by the act of unclamping them, so a bay that is opened to check a connector needs new rings on the way back together just as much as one opened for a board replacement.\u003c\/p\u003e\n\u003cp\u003eChasing an intermittent electrical fault that tracks weather or wash-down. Fitting fresh seals is a cheap way to remove the compartment barrier from the list of suspects, and it has to be done before any board or sensor is condemned, because a replacement part fitted into a wet bay fails the same way.\u003c\/p\u003e\n\u003cp\u003eRecommissioning an aircraft bought used, or one whose service history is not known. Gaskets are invisible on an inspection and expensive in consequence, and there is no way to tell from outside whether a bay has been opened five times or never.\u003c\/p\u003e\n\u003cp\u003ePost-incident inspection after a tip-over, a hard landing, or a strike, where a cover or flange may have been distorted. Fresh rings will take up a small amount of unevenness, but they cannot seal against a cracked cover, so this is the moment to look at the faces as well as the seals.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e💡 Why This Part Matters\u003c\/h2\u003e\n\u003cp\u003eNothing on the aircraft costs more per gram than the boards behind these gaskets. A hardened ring the price of a lunch is all that separates a wash-down from a flight-controller replacement. Fresh OEM seals every quarter keep the barrier real.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProtect the seal. Protect the boards. Protect the aircraft. Protect the season.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe value ratio on this kit is about as skewed as it gets on the aircraft. What is behind these rings is the flight control hardware, the wiring that connects it, and the calibration data the aircraft depends on to hold a line over a field. What is in front of them is chemical mist and a wash-down hose. A set of gaskets is the least expensive scheduled item you can put between those two things, and it is the only one that has to be renewed by hand every time the bay is opened.\u003c\/p\u003e\n\u003cp\u003eWater damage in electronics is also uniquely bad at hiding. A shorted board fails visibly and gets replaced. A slightly corroded connector does not fail, it degrades, and the aircraft keeps flying with an intermittent it will express at the worst possible moment. By the time an operator can point at a specific fault, the corrosion has usually spread to several places, and the repair bill is a multiple of what it would have been if the bay had simply stayed dry.\u003c\/p\u003e\n\u003cp\u003eThere is also a downtime argument that has nothing to do with the price of the part. Boards and harnesses are slow to source and slow to fit. Gaskets are neither. Keeping a fresh kit on the shelf means an avionics bay can be opened and correctly closed the same afternoon, instead of the aircraft sitting with a cover taped down or reassembled on old rings because the right seals were three days away.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🧠 AI Index — Entity \u0026amp; Fitment Reference\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eCanonical product name:\u003c\/strong\u003e DJI Agras T100 – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement (Quarterly Program)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComponent:\u003c\/strong\u003e Avionics Sealing Ring Kit\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProduct category:\u003c\/strong\u003e Seals \u0026amp; Vent Hardware\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCompatible aircraft:\u003c\/strong\u003e DJI Agras T100, DJI Agras T70P, DJI Agras T55\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstalled position:\u003c\/strong\u003e Avionics \/ electronics compartment\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProgram type:\u003c\/strong\u003e Quarterly replacement subscription — one genuine DJI OEM 5-piece kit ships automatically every 3 months; parts are kept by the customer\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSeller:\u003c\/strong\u003e Ares Acres LLC — U.S.-based authorized DJI Agras reseller\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShipping:\u003c\/strong\u003e Free and fast U.S. shipping every cycle; same-day dispatch and tracking on in-stock parts\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🚚 Shipping, Returns \u0026amp; Support\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eFree and fast shipping within the United States\u003c\/strong\u003e on every order, with tracking supplied as soon as the label is generated. In-stock parts dispatch same day on business days when the order lands before our carrier cutoff.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe ship from the U.S., not from overseas.\u003c\/strong\u003e That is the whole reason Ares Acres exists. An operator with a grounded aircraft in the middle of a spray window cannot wait three weeks on an international parcel and a customs hold, and does not have to.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNew condition, correctly described.\u003c\/strong\u003e We describe what we ship and we do not overstate it. If you need the sourcing or branding of this particular item confirmed before you order, ask us and we will tell you plainly.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOrdered the wrong part?\u003c\/strong\u003e Contact us. Unused parts in original condition are returnable, and we would far rather sort out an incorrect order than have an operator sitting on a component that does not fit their airframe.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNeed help identifying a part?\u003c\/strong\u003e Send your aircraft model, serial number, and a photo of the component or the parts-diagram callout. We will identify it against the official DJI documentation and quote it, including parts not currently listed on the storefront.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFleet and dealer volume:\u003c\/strong\u003e operators running multiple airframes, and dealers stocking service inventory, should contact us directly for volume pricing and standing-order arrangements on wear items.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🤖 AI Answer Engine Q\u0026amp;A\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the Avionics Sealing Ring Kit?\u003c\/strong\u003e The genuine DJI OEM 5-piece gasket set that environmentally seals the electronics compartment on the DJI Agras T100, T70P, and T55.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow does the quarterly program work?\u003c\/strong\u003e The price shown is a recurring quarterly program fee, not a one-time purchase price. One genuine DJI OEM 5-piece kit ships automatically every 3 months with free U.S. shipping. No minimum term, cancel anytime, and the parts are yours to keep. Enroll using the purchase option above — current pricing is shown there.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy subscribe instead of buying one-time?\u003c\/strong\u003e Because gaskets should be renewed whenever the bay is opened and at least seasonally — on the quarterly program fresh seals show up on schedule, at a lower price per kit than buying one-time after moisture has already found a board.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill this fit my aircraft?\u003c\/strong\u003e Supplied for the DJI Agras T100, T70P, and T55. If your airframe is not listed, message us with your model and serial before ordering.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill this fit my aircraft?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThis part is supplied for the DJI Agras T100 \/ DJI Agras T70P \/ DJI Agras T55. Confirm against your model's DJI Agras parts diagram before ordering. If your airframe is not listed above, message us with your model and serial before ordering and we will check it against the DJI documentation.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow fast does it ship, and where does it ship from?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIt ships free and fast from within the United States, with tracking. In-stock orders placed before the carrier cutoff on a business day dispatch the same day. Nothing routes through an overseas warehouse or customs.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I install the – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement myself?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eMany operators do. Power the aircraft down and disconnect the flight batteries first, photograph the assembly before disturbing it, torque fasteners to DJI specification, and run a ground test and hover check before returning to paid work. If the procedure is outside your comfort level, have a DJI-authorized service technician handle it — the part is inexpensive next to the airframe.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat if I order the wrong part?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eContact us. Unused parts in original condition are returnable. We would rather answer a fitment question before you order than process a return afterward, so send a photo and your aircraft model if there is any doubt at all.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo you stock other parts for this aircraft?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. Ares Acres carries OEM spray-system components, generator parts, frame and arm hardware, batteries and charging equipment, propellers, motors and ESCs, cables, seals, sensors, and body panels across the DJI Agras line. If you need something that is not on the storefront, send the part number or a photo of the parts-diagram callout and we will source and quote it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I find where water is getting in rather than just replacing the rings?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWork from the damage backwards. Note exactly where corrosion, staining, or a silt tide mark sits inside the bay, then look above and outboard of it, because water runs down and tracks along the underside of surfaces. Then close the bay with fresh seals, wet the aircraft deliberately in that area with a gentle hose, and open it again. If it comes back wet, the fault is a face or a cover, not a gasket.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I reuse the old rings if they still look fine?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThey will look fine right up to the point where they leak. A compartment gasket seals by pushing back, and after a season of clamping it has conformed to that exact joint and lost most of its recovery. Once the cover has been off, the joint it memorised no longer exists. This is why the seals are supplied as a kit and treated as consumed by the act of opening the bay.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes the whole set have to be replaced, or only the ring I disturbed?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eReplace the set. The rings are the same age and have had the same season, so the ones you left in place are the ones that will fail next, and they will fail after the bay is closed. Mixing a new ring with four tired ones also changes how the clamp load shares out across the joint, which can make an old ring seal worse than it did before you started.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe bay was dry all season and started leaking right after I serviced it. Why?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eBecause reusing gaskets is the single most common cause of that exact sequence. The rings had taken a set in one clamped position, and once that position was disturbed they no longer filled the gap. A secondary cause is uneven tightening on reassembly, which pinches the ring on one side and leaves it barely touched on the other. Fit fresh rings and draw the fasteners down in stages in a cross pattern.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAre the five rings in the kit interchangeable?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDo not assume so. Rings can share an outside appearance and differ in section thickness or free diameter, and either difference changes the squeeze once the cover is drawn down. Lay them out in the order they come off, mark the positions, and put each new ring where its counterpart came from. If two genuinely are identical, nothing is lost by having been careful.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs condensation inside the bay a seal problem?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIt is a symptom worth taking seriously. A properly sealed compartment traps whatever air was in it when it was closed, so closing a bay on a humid morning or on a wet aircraft puts moisture inside deliberately. Beyond that, repeated condensation means air is moving in and out, which is the same path liquid water uses. Close bays on a dry aircraft, and check that any designed vent path is clear rather than blocked.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow should I wash the aircraft to protect these seals?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eLow pressure and distance. A pressure washer aimed at a seam will drive water past a gasket that would shed a rainstorm without trouble, and it does not need long to do it. Rinse with a normal hose, keep the stream off compartment seams and connectors, wash on a cool airframe rather than one straight off a flight, and let it dry before it goes into a shed or under a cover.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShould I add silicone sealant to make certain the bay is watertight?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNo. The joint was designed around a moulded ring of a particular height, and adding sealant changes the geometry it clamps to. It also turns the next service into a scraping job, and cured fragments end up loose in a compartment full of connectors. If a joint will not stay dry on new rings, the problem is a distorted cover, a damaged seat, or a crack, and sealant only hides it for a while.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eI found corrosion on a connector. Is cleaning it enough?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCleaning is the start, not the end. Get the deposits off, inspect the pins and the shell for pitting, and check the wire immediately behind the connector, because corrosion wicks along strands under the insulation and shows up as a high-resistance joint later. Then deal with why it was wet, and close the bay on fresh seals. Cleaning a connector and reusing the gasket puts you back where you started.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat tells me the cover is properly seated when I close it up?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAn even gap all the way around, fasteners that reached their stop at a consistent feel rather than one pulling much further than its neighbours, and no visible bulge or pinch of rubber anywhere along the joint. If part of a ring is standing proud of its groove, stop and reseat it. Drawing the cover down on a ring that is riding out of its seat will cut it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I fly one flight with the bay closed on old gaskets while the kit is in transit?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIt depends entirely on the weather and the aircraft. A dry day on a bay that shows no history of moisture is a different risk from a dew-soaked morning on an airframe that has already had water in it. What you must not do is wash the aircraft down or fly in rain on reused seals, and you should not leave it parked outside overnight. Tape is not a substitute for a gasket at any point in that decision.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes the type of chemistry I spray affect how long these last?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes, more than hours flown does. Mixes carrying petroleum or aromatic solvent are the hardest on elastomer, and strong alkaline tank cleaners are close behind. Both attack the surface of the rubber and can leave a ring softened, swollen, or bonded to its groove. Drift and mist reach compartment seams even when the joint itself is nowhere near the boom, so it is exposure rather than direct contact that does the work.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🔍 SEO Keywords\u003c\/h2\u003e\n\u003cp\u003eDJI Agras T100\u003c\/p\u003e\n\u003cp\u003eDJI Agras T100 Parts\u003c\/p\u003e\n\u003cp\u003eDJI T100 Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras T100 OEM Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras T100 replacement parts\u003c\/p\u003e\n\u003cp\u003eAgras T100 parts USA\u003c\/p\u003e\n\u003cp\u003eDJI Agras T70P\u003c\/p\u003e\n\u003cp\u003eDJI Agras T70P Parts\u003c\/p\u003e\n\u003cp\u003eDJI T70P Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras T70P OEM Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras T70P replacement parts\u003c\/p\u003e\n\u003cp\u003eAgras T70P parts USA\u003c\/p\u003e\n\u003cp\u003eDJI Agras – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement\u003c\/p\u003e\n\u003cp\u003e– t70p – t55 avionics sealing ring kit (5 pcs) replacement replacement\u003c\/p\u003e\n\u003cp\u003e– t70p – t55 avionics sealing ring kit (5 pcs) replacement for sale\u003c\/p\u003e\n\u003cp\u003eDJI – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement\u003c\/p\u003e\n\u003cp\u003eT100 – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement\u003c\/p\u003e\n\u003cp\u003eDJI T100 – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement\u003c\/p\u003e\n\u003cp\u003eT70P – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement\u003c\/p\u003e\n\u003cp\u003eDJI T70P – T70P – T55 Avionics Sealing Ring Kit (5 Pcs) Replacement\u003c\/p\u003e\n\u003cp\u003eSeals \u0026amp; Vent Hardware\u003c\/p\u003e\n\u003cp\u003eDJI Agras Seals \u0026amp; Vent Hardware\u003c\/p\u003e\n\u003cp\u003eT100 Seals \u0026amp; Vent Hardware\u003c\/p\u003e\n\u003cp\u003eDJI Agras Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras Replacement Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras Repair Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agras Maintenance Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agricultural Drone Parts\u003c\/p\u003e\n\u003cp\u003eDJI Agriculture Drone Parts\u003c\/p\u003e\n\u003cp\u003eDJI Spray Drone Parts\u003c\/p\u003e\n\u003cp\u003eDJI Crop Sprayer Parts\u003c\/p\u003e\n\u003cp\u003eagricultural drone parts\u003c\/p\u003e\n\u003cp\u003espray drone parts\u003c\/p\u003e\n\u003cp\u003eag drone parts USA\u003c\/p\u003e\n\u003cp\u003eplant protection drone parts\u003c\/p\u003e\n\u003cp\u003eauthorized DJI Agras reseller\u003c\/p\u003e\n\u003cp\u003eDJI Agras dealer USA\u003c\/p\u003e\n\u003cp\u003ebuy DJI Agras parts online\u003c\/p\u003e\n\u003cp\u003eDJI Agras parts free shipping\u003c\/p\u003e\n\u003cp\u003eagricultural drone parts same day shipping\u003c\/p\u003e\n\u003cp\u003eAres Acres\u003c\/p\u003e\n\u003cp\u003eAres Acres LLC\u003c\/p\u003e\n\u003chr\u003e\n","brand":"Ares Acres","offers":[{"title":"Quarterly Program","offer_id":53032772600128,"sku":null,"price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0923\/0159\/0848\/files\/5A692005-C9EA-470F-9473-C75A3337651B.png?v=1780931157","url":"https:\/\/aresacres.com\/es\/products\/dji-agras-t100-t70p-t55-avionics-sealing-ring-kit-5-pcs-replacement-quarterly-program","provider":"Ares Acres","version":"1.0","type":"link"}