{"product_id":"dji-talos-t60x-oem-weight-sensor-rubber-cover","title":"DJI Talos T60X OEM Weight Sensor Rubber Cover","description":"\u003cp\u003eThe DJI Talos T60X OEM Weight Sensor Rubber Cover is the round black rubber cover that protects a weight sensor in the payload weighing system of the Talos T60X. The product images show a circular rubber cover with a wide outer ring, a raised inner ring, a round central opening with two small lugs on its inner edge, and two fine lines across the outer ring at opposite points. It is a payload-system seal: it carries no load and makes no measurement, but it keeps spray residue, fertiliser solution and wash water away from the sensor it covers. It is identified for the Talos T60X. Send us a photograph of the label on the part you removed and we will match it before it ships. Operators usually come looking for a Talos T60X weight sensor cover, load sensor boot or weighing sensor rubber after the old cover has split or hardened, after it was lost during tank work, or after residue has been found packed around a sensor that was supposed to be covered.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🇺🇸 U.S.A. FIRST\u003c\/h2\u003e\n\u003cp\u003eAres Acres LLC is a U.S.-based authorized DJI retailer supplying agricultural spray aircraft, replacement components, and field-ready inventory to American commercial operators, service centres, and applicators.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFREE \u0026amp; FAST Shipping is included for all U.S. customers.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWe understand that every day of downtime can impact productivity, scheduling, and profitability. That's why we focus on providing fast fulfillment, responsive customer support, and reliable access to the parts operators need most.\u003c\/p\u003e\n\u003cp\u003eAres Acres also ships agricultural drone parts to Canada, with free shipping included on Canadian orders. Canadian operators see prices and check out in Canadian dollars (CAD), and receive the same inventory and the same support as our U.S. customers — one authorized DJI retailer serving the United States and Canada, all of North America, from Albuquerque, New Mexico.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e✅ DJI Talos T60X Compatibility Guarantee\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e🇺🇸 USA Compatibility Guarantee\u003c\/li\u003e\n\u003cli\u003e👍🏻 Satisfaction Guarantee\u003c\/li\u003e\n\u003cli\u003e💵 Money Back Guarantee\u003c\/li\u003e\n\u003cli\u003e📦 Same Day Shipping \u0026amp; Tracking\u003c\/li\u003e\n\u003cli\u003eIdentified for the Talos T60X\u003c\/li\u003e\n\u003cli\u003eMatched by outline, rings, central opening and lugs against the cover you removed\u003c\/li\u003e\n\u003cli\u003eGenuine DJI OEM payload-system rubber cover, brand new\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSend us a photograph of the label on the part you removed and we will match it before it ships. If the old cover is lost, a photograph of the weight sensor position it came from is enough to start the match.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e📦 Package Includes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e1 × DJI Talos T60X OEM Weight Sensor Rubber Cover\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eOne cover, one sensor.\u003c\/strong\u003e The cover protects one weight sensor at one weighing point. It is not a set for every weighing point on the aircraft.\u003c\/p\u003e\n\u003cp\u003eNot included: the Weight Sensor Module, the Weight Sensor Bracket, the Weight Sensor Signal Cable, the Sealing Rings, and any fixings. Those are separate parts.\u003c\/p\u003e\n\u003cp\u003eNothing is included because it appears in a photograph. The photograph shows the rubber cover alone.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🔧 Component Overview\u003c\/h2\u003e\n\u003cp\u003eEach weighing point on the Talos T60X has a Weight Sensor Module that measures the load passing through it. The sensor works by detecting very small changes under load, which makes it sensitive to anything that packs around it: dried spray mix, fertiliser crystals, soil and grit carried in by wash water. The rubber cover is what keeps that material off.\u003c\/p\u003e\n\u003cp\u003eIn the product images the cover is a round black rubber part. A wide outer ring surrounds a raised inner ring, and the inner ring frames a round central opening. Two small lugs project into the opening from its edge, and two fine lines cross the outer ring at opposite points. The rubber is flexible, so it can be stretched over and around the part it protects and then grip it.\u003c\/p\u003e\n\u003cp\u003eThe cover carries no load and no signal. It does not touch the measurement. Its value is entirely in what it keeps out, and that makes it one of the few payload-system parts whose failure is silent: when the cover splits or hardens, nothing changes on the remote controller. The sensor simply begins to collect residue it was protected from, and the weight reading drifts later, for a reason that is hard to trace back.\u003c\/p\u003e\n\u003cp\u003eWhat the rubber cover lives with, over a working season:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSpray mixes and fertiliser solutions splashing and settling in the payload area\u003c\/li\u003e\n\u003cli\u003ePressure washing at the end of a spray day, aimed at the area it protects\u003c\/li\u003e\n\u003cli\u003eSunlight and heat whenever the aircraft is parked outside\u003c\/li\u003e\n\u003cli\u003eStretching and refitting every time the sensor beneath it is inspected\u003c\/li\u003e\n\u003cli\u003eTank and payload removal, which can catch or drag it\u003c\/li\u003e\n\u003cli\u003eVibration from the propulsion system, which works at any loose edge\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWhat ends its life is the rubber itself: a tear that starts at an edge or at one of the lines across the ring, rubber that has hardened and no longer grips, a lug torn off, or a cover that has been lost during tank work. The first two are easy to miss, because a split or hardened cover can still sit in place.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e⚙️ Functional Purpose\u003c\/h2\u003e\n\u003cp\u003eThe rubber cover's engineering role is to keep contamination away from a weight sensor. It does that in three ways:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCovering\u003c\/strong\u003e — the outer and inner rings shield the sensor from direct splash and wash water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGripping\u003c\/strong\u003e — the flexible rubber and the lugs at the central opening hold the cover on its position\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExcluding\u003c\/strong\u003e — the fit of the rubber against the parts around it stops residue and grit from working in\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe cover only works while the rubber is intact and still flexible. Rubber that has split lets water in through the split. Rubber that has hardened no longer presses against the surfaces around it, so it lets water in around its edge. In both cases the cover is still visibly there.\u003c\/p\u003e\n\u003cp\u003eWhat the rubber cover does not do:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eIt does not measure anything; the Weight Sensor Module does\u003c\/li\u003e\n\u003cli\u003eIt does not hold the sensor in position; the Weight Sensor Bracket does\u003c\/li\u003e\n\u003cli\u003eIt does not seal a liquid joint in the spray system; those are the Sealing Rings\u003c\/li\u003e\n\u003cli\u003eIt does not restore a sensor that is already contaminated or damaged\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch2\u003e🔍 Diagnosis — a cover that is still in place can already have stopped working\u003c\/h2\u003e\n\u003cp\u003eA missing cover is obvious. A failed cover usually is not. The rubber cover protects the sensor by its fit, and a cover that has split along one of its lines, or hardened so it no longer grips, still sits in place and still looks like protection. Water and residue go past it all the same.\u003c\/p\u003e\n\u003cp\u003eNothing reports that failure. The cover has no wire and no warning. The only evidence is what you find under it, and that evidence arrives late: residue packed around the sensor, a sensor that has started to read differently, or grit in a place that should have stayed clean.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInspect the cover itself:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eClean it and look along both lines that cross the outer ring; a line that has opened into a gap is a split\u003c\/li\u003e\n\u003cli\u003eLook around the outer edge and the central opening for tears and nicks\u003c\/li\u003e\n\u003cli\u003eCheck both lugs at the central opening are present\u003c\/li\u003e\n\u003cli\u003eFlex the rubber between your fingers; it should bend and spring back, not crack or stay bent\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eThen look under it:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eEase the cover back and look at the sensor and the area around it\u003c\/li\u003e\n\u003cli\u003eDried residue, fertiliser crystals or grit under the cover mean the cover has been letting material in\u003c\/li\u003e\n\u003cli\u003eA clean, dry area under the cover means it is still doing its job\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSigns that point away from the cover:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe weight reading is wrong but the area under the cover is clean — test the sensor and its bracket instead\u003c\/li\u003e\n\u003cli\u003eEvery weighing reading is missing at once — look at the Weight Sensor Signal Cable\u003c\/li\u003e\n\u003cli\u003eA liquid joint is weeping in the spray system — that is a sealing ring, not this cover\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLift the cover and look under it first, while that information is still cheap. It takes a minute and tells you whether the cover has failed and whether the sensor beneath it needs attention as well.\u003c\/p\u003e\n\u003cp\u003eA cover that is split, hardened or missing a lug should be replaced even if the sensor beneath it is still clean. It will not stay clean.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e⚠️ Common Replacement Indicators\u003c\/h2\u003e\n\u003cp\u003eReplace the weight sensor rubber cover when inspection confirms one of these:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA split along one of the lines across the outer ring, or a tear anywhere in the rubber\u003c\/li\u003e\n\u003cli\u003eRubber that has hardened, cracks when flexed, or no longer springs back\u003c\/li\u003e\n\u003cli\u003eA lug missing from the central opening\u003c\/li\u003e\n\u003cli\u003eA cover that no longer grips and lifts away from its position\u003c\/li\u003e\n\u003cli\u003eResidue, crystals or grit found under the cover\u003c\/li\u003e\n\u003cli\u003eA cover lost during tank or payload work\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInspect these as well, because they are often affected together:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe Weight Sensor Module under the cover, for residue around its contact\u003c\/li\u003e\n\u003cli\u003eThe Weight Sensor Bracket that holds the sensor\u003c\/li\u003e\n\u003cli\u003eThe covers at the other weighing points, which have lived through the same conditions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThere is no published service interval for the weight sensor rubber cover. It is replaced when it is damaged, hardened or lost.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e📐 Specifications\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eProduct name:\u003c\/strong\u003e DJI Talos T60X OEM Weight Sensor Rubber Cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDJI family:\u003c\/strong\u003e Talos\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFitment basis:\u003c\/strong\u003e Identified for the Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVariant:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft system:\u003c\/strong\u003e Payload system — weighing\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComponent type:\u003c\/strong\u003e Weight sensor rubber cover (protective seal)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial number:\u003c\/strong\u003e Not published for this part — Send us a photograph of the label on the part you removed and we will match it before it ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuantity:\u003c\/strong\u003e 1 cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAppearance:\u003c\/strong\u003e Round black rubber cover with a wide outer ring, raised inner ring, round central opening with two small lugs, and two fine lines across the outer ring, as photographed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eColour:\u003c\/strong\u003e Black, as photographed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial:\u003c\/strong\u003e Rubber, as named in the part designation; compound not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eElectrical:\u003c\/strong\u003e None\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMounting position:\u003c\/strong\u003e At a weight sensor in the payload weighing system; compare with the cover you removed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation method:\u003c\/strong\u003e Fitted over its position by hand and held by the grip of the rubber\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIncluded hardware:\u003c\/strong\u003e None\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eService adjustability:\u003c\/strong\u003e None — the part is correct or it is not, with no adjustment or app setting that compensates\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCondition:\u003c\/strong\u003e Brand new\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eClassification:\u003c\/strong\u003e DJI OEM payload-system rubber cover\u003c\/p\u003e\n\n\u003chr\u003e\n\u003ch2\u003e🛠️ Installation \u0026amp; Maintenance\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eBefore installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePower the aircraft down and remove the battery\u003c\/li\u003e\n\u003cli\u003eEmpty and rinse the tank so the payload area is clean and unloaded\u003c\/li\u003e\n\u003cli\u003ePhotograph the old cover in place, showing which way its lines and lugs face\u003c\/li\u003e\n\u003cli\u003eCompare the new cover with the old one: outer ring, inner ring, central opening and lugs\u003c\/li\u003e\n\u003cli\u003eHave a clean, lint-free cloth ready for the area under the cover\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eDuring installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eEase the old cover off by hand, working round its edge; do not lever it with a screwdriver against the sensor\u003c\/li\u003e\n\u003cli\u003eInspect the sensor and the area under the cover and clean away any residue, crystals or grit\u003c\/li\u003e\n\u003cli\u003eLet the area dry before covering it again, so water is not sealed in\u003c\/li\u003e\n\u003cli\u003eFit the new cover in the same orientation as the old one, lugs aligned the same way\u003c\/li\u003e\n\u003cli\u003eWork the rubber round its position by hand until it sits evenly with no lifted edge\u003c\/li\u003e\n\u003cli\u003eDo not use grease or solvent on the rubber unless DJI service guidance for the aircraft calls for it\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eAfter installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRun a finger round the edge and confirm the cover grips all the way round\u003c\/li\u003e\n\u003cli\u003ePower up on the ground and confirm there are no warnings on the remote controller\u003c\/li\u003e\n\u003cli\u003eRun a known-weight test with clean water if residue was found under the old cover\u003c\/li\u003e\n\u003cli\u003eRecord the replacement and what was found under the old cover in the maintenance log\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eMaintenance between jobs.\u003c\/strong\u003e Rinse the payload area at the end of a spray day, but avoid holding a pressure-washer jet directly on the cover edge at close range; that is how water is driven past a cover that is otherwise sound. Flex-check the covers at each weighing point at the start of the season, because rubber hardens in storage as well as in use.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🚜 Necessary For\u003c\/h2\u003e\n\u003cp\u003eThe weight sensor rubber cover is for operators and technicians keeping the Talos T60X weighing system clean and accurate:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTalos T60X operators with a cover that has split, hardened or gone missing\u003c\/li\u003e\n\u003cli\u003eTalos T60X operators who have found residue packed under a cover\u003c\/li\u003e\n\u003cli\u003eCommercial spray contractors running fertiliser and high-residue mixes through the season\u003c\/li\u003e\n\u003cli\u003eService centres and repair technicians rebuilding payload areas\u003c\/li\u003e\n\u003cli\u003eFleet managers stocking spare covers for the trailer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eThis is not the part you need if:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe cover is intact and the weight reading is still wrong — test the Weight Sensor Module and the Weight Sensor Bracket\u003c\/li\u003e\n\u003cli\u003eThe sensor itself is cracked or reads wrong after a swap test — you need the Weight Sensor Module\u003c\/li\u003e\n\u003cli\u003eEvery weighing reading is missing at once — look at the Weight Sensor Signal Cable\u003c\/li\u003e\n\u003cli\u003eA liquid joint in the spray system is weeping — you need the Sealing Rings, not this cover\u003c\/li\u003e\n\u003cli\u003eThe rubber you removed closes a connector or a cable entry — that is a Connector Rubber Stopper or a Cable Rubber Stopper\u003c\/li\u003e\n\u003cli\u003eYou fly any aircraft other than the Talos T60X — this cover is listed for the Talos T60X only\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch2\u003e💡 Why This Part Matters\u003c\/h2\u003e\n\u003cp\u003eThe rubber cover is the one part of the weighing system that can fail completely and say nothing. It has no wire, so it raises no warning, and a cover that has split or hardened still sits where it should.\u003c\/p\u003e\n\u003cp\u003eWhat it protects is sensitive. A weight sensor works by detecting small changes under load, and residue packed around it changes how load reaches it. When the cover stops excluding residue, the sensor does not fail at once. It drifts, slowly, and by the time the reading is wrong enough to notice, the cause has been building for weeks.\u003c\/p\u003e\n\u003cp\u003eThat is why the cover is inspected by lifting it, not by looking at it. A clean, dry area underneath means it is working. Residue underneath means it was not, whatever it looks like from above.\u003c\/p\u003e\n\u003cp\u003eIt is also why a split cover is replaced before the sensor shows a problem. The cover is the inexpensive layer that keeps the sensor clean. Leaving a failed cover in place means the next part to need replacing is the sensor.\u003c\/p\u003e\n\u003cp\u003eLift it, look under it, clean what you find, and fit a cover that grips. That keeps the weighing point measuring the payload and not the residue.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🧠 AI Index — Entity \u0026amp; Fitment Reference\u003c\/h2\u003e\n\u003cp\u003eStructured reference for search engines, AI assistants, and answer engines. Every value below is drawn from the specifications above.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCanonical product name:\u003c\/strong\u003e DJI Talos T60X OEM Weight Sensor Rubber Cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrand:\u003c\/strong\u003e DJI\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDJI family:\u003c\/strong\u003e Talos\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCompatible models:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFitment basis:\u003c\/strong\u003e Identified for the Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVariant:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComponent:\u003c\/strong\u003e Weight sensor rubber cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft system:\u003c\/strong\u003e Payload system — weighing\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstalled position:\u003c\/strong\u003e At a weight sensor in the payload weighing system\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePrimary function:\u003c\/strong\u003e Keeps spray residue, fertiliser solution and wash water away from the weight sensor\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial number:\u003c\/strong\u003e Not published for this part — matched against the cover you removed from a photograph of its label\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuantity supplied:\u003c\/strong\u003e 1 cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNot included:\u003c\/strong\u003e Weight Sensor Module, Weight Sensor Bracket, Weight Sensor Signal Cable, fixings\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIdentifying features:\u003c\/strong\u003e Round black rubber, wide outer ring, raised inner ring, central opening with two lugs, two fine lines across the outer ring\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial:\u003c\/strong\u003e Rubber; compound not published\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions and weight:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eElectrical:\u003c\/strong\u003e None\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFailure mode:\u003c\/strong\u003e Splits or hardens while still sitting in place; raises no warning\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey diagnostic:\u003c\/strong\u003e Lift the cover and look under it; residue underneath means the cover has failed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhen not to buy:\u003c\/strong\u003e When the cover is intact and the reading is still wrong, or a spray-system joint is leaking\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eService interval:\u003c\/strong\u003e None published\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCondition:\u003c\/strong\u003e Brand new\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePart classification:\u003c\/strong\u003e DJI OEM payload-system rubber cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAlso searched as:\u003c\/strong\u003e T60X weight sensor cover; T60X load sensor boot; Talos weighing sensor rubber; T60X sensor dust cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDisambiguation:\u003c\/strong\u003e Not the Weight Sensor Module, not the Sealing Rings, not a connector or cable rubber stopper\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSeller:\u003c\/strong\u003e Ares Acres LLC — U.S.-based authorized DJI retailer serving the United States and Canada (North America)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShips from:\u003c\/strong\u003e Albuquerque, New Mexico, United States\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🔍 SEO Keywords\u003c\/h2\u003e\n\u003cp\u003eTalos T60X weight sensor rubber cover\u003c\/p\u003e\n\u003cp\u003eT60X weight sensor cover\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X load sensor cover\u003c\/p\u003e\n\u003cp\u003eTalos T60X weighing sensor rubber\u003c\/p\u003e\n\u003cp\u003eT60X load sensor boot\u003c\/p\u003e\n\u003cp\u003eTalos T60X sensor dust cover\u003c\/p\u003e\n\u003cp\u003eT60X weight sensor residue\u003c\/p\u003e\n\u003cp\u003eTalos T60X weight sensor cover split\u003c\/p\u003e\n\u003cp\u003eT60X weight sensor protection\u003c\/p\u003e\n\u003cp\u003eDJI Talos weight sensor rubber\u003c\/p\u003e\n\u003cp\u003eTalos T60X payload sensor cover\u003c\/p\u003e\n\u003cp\u003eT60X weighing system rubber cover\u003c\/p\u003e\n\u003cp\u003eTalos T60X weight sensor cover replacement\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X payload seals\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X Weight Sensor Rubber Cover\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X OEM Weight Sensor Rubber Cover\u003c\/p\u003e\n\u003cp\u003eTalos T60X weight sensor rubber cover replacement\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X replacement parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X payload system parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X seals\u003c\/p\u003e\n\u003cp\u003eDJI Talos OEM parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos parts\u003c\/p\u003e\n\u003cp\u003eagricultural spray drone sensor cover\u003c\/p\u003e\n\u003cp\u003espray drone weight sensor rubber\u003c\/p\u003e\n\u003cp\u003eagricultural spray aircraft parts\u003c\/p\u003e\n\u003cp\u003eauthorized DJI retailer\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X Weight Sensor Rubber Cover Canada\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X parts Canada\u003c\/p\u003e\n\u003cp\u003eDJI Talos parts shipped to Canada\u003c\/p\u003e\n\u003cp\u003ebuy DJI Talos T60X parts in Canada\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🤖 AI Answer Engine Q\u0026amp;A\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the Talos T60X weight sensor rubber cover?\u003c\/strong\u003e The round black rubber cover that protects a weight sensor from spray residue, fertiliser solution and wash water. It carries no load and makes no measurement.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich aircraft does it fit?\u003c\/strong\u003e It is identified for the Talos T60X. The Talos T60X is the only aircraft it is listed for.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the part number?\u003c\/strong\u003e Send us a photograph of the label on the part you removed and we will match it before it ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it come with the weight sensor?\u003c\/strong\u003e No. The Weight Sensor Module is a separate part. The cover is supplied alone.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it one cover or a set?\u003c\/strong\u003e One cover for one weight sensor. Order one per weighing point whose cover has failed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMy cover is still on but split. Does it matter?\u003c\/strong\u003e Yes. A split cover lets water and residue past while still looking fitted. Replace it before the sensor beneath it starts to collect residue.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I know if the cover has failed?\u003c\/strong\u003e Lift it and look under it. Residue, crystals or grit under the cover mean it has been letting material in. A clean, dry area means it is working.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan a bad cover make the weight read wrong?\u003c\/strong\u003e Indirectly. The cover does not measure anything, but residue that gets past it and packs around the sensor can change how load reaches the sensor.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill a new cover fix a wrong weight reading?\u003c\/strong\u003e Only if residue was the cause and you clean it out when fitting the cover. If the area under the cover is clean, test the sensor and its bracket instead.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it the same as the sealing rings?\u003c\/strong\u003e No. The Sealing Rings seal liquid joints in the spray system. This cover protects a weight sensor in the weighing system.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it a connector stopper?\u003c\/strong\u003e No. A Connector Rubber Stopper closes a connector, and a Cable Rubber Stopper sits on a cable. This cover sits over a weight sensor.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat are the lines across the ring?\u003c\/strong\u003e The product images show two fine lines across the outer ring at opposite points. Check them closely on the old cover; an opened line is where a split usually shows.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I fit it myself?\u003c\/strong\u003e Yes. Ease the old cover off by hand, clean and dry the area, fit the new cover in the same orientation and work it round until it grips evenly.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I pressure-wash around it?\u003c\/strong\u003e Yes, but keep the jet off the cover edge at close range. A direct jet at the edge can drive water past a sound cover.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs there a service interval?\u003c\/strong\u003e No published interval. Flex-check the covers at the start of each season and replace any that are split, hardened or lost.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it a genuine DJI part?\u003c\/strong\u003e Yes. It is a genuine DJI OEM payload-system rubber cover, brand new.\u003c\/p\u003e","brand":"Ares Acres","offers":[{"title":"Talos T60X","offer_id":68055437476160,"sku":null,"price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0923\/0159\/0848\/files\/dji-talos-t60x-oem-weight-sensor-rubber-cover-1.png?v=1794094892","url":"https:\/\/aresacres.com\/es\/products\/dji-talos-t60x-oem-weight-sensor-rubber-cover","provider":"Ares Acres","version":"1.0","type":"link"}