{"product_id":"dji-talos-t60x-oem-rear-cover-of-rear-shell","title":"DJI Talos T60X OEM Rear Cover of Rear Shell","description":"\u003cp\u003eThe DJI Talos T60X OEM Rear Cover of Rear Shell is the long, dark-grey outer cover that closes the rear of the body shell on the Talos T60X. The supplier photograph shows a wide, shallow, curved moulding with a row of clips and tabs along its upper edge, a single tab near the centre, angled faces stepping down toward each end, and smaller tabs along its lower edge. It is an airframe shell component with no wiring or electronics of its own: the outer skin of the rear shell, held in place mostly by its clips. It is listed by the supplier for the Talos T60X. Send us a photograph of the label on the part you removed and we will match it before it ships. Most rear covers are ordered because they will not stay seated, and a cover that will not stay seated is not always a broken cover. The clips on the cover and the places they clip into fail in the same way from the outside, and only one of them is fixed by this part.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🇺🇸 U.S.A. FIRST\u003c\/h2\u003e\n\u003cp\u003eAres Acres LLC is a U.S.-based authorized DJI retailer supplying agricultural spray aircraft, replacement components, and field-ready inventory to American commercial operators, service centres, and applicators.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFREE \u0026amp; FAST Shipping is included for all U.S. customers.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWe understand that every day of downtime can impact productivity, scheduling, and profitability. That's why we focus on providing fast fulfillment, responsive customer support, and reliable access to the parts operators need most.\u003c\/p\u003e\n\u003cp\u003eAres Acres also ships agricultural drone parts to Canada, with free shipping included on Canadian orders. Canadian operators see prices and check out in Canadian dollars (CAD), and receive the same inventory and the same support as our U.S. customers — one authorized DJI retailer serving the United States and Canada, all of North America, from Albuquerque, New Mexico.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e✅ DJI Talos T60X Compatibility Guarantee\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e🇺🇸 USA Compatibility Guarantee\u003c\/li\u003e\n\u003cli\u003e👍🏻 Satisfaction Guarantee\u003c\/li\u003e\n\u003cli\u003e💵 Money Back Guarantee\u003c\/li\u003e\n\u003cli\u003e📦 Same Day Shipping \u0026amp; Tracking\u003c\/li\u003e\n\u003cli\u003eListed by the supplier for the DJI Talos T60X\u003c\/li\u003e\n\u003cli\u003eMatched by outline, curvature, upper clip row, centre tab and lower tabs against the rear cover you removed\u003c\/li\u003e\n\u003cli\u003eGenuine DJI OEM airframe shell component, brand new\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIf you want the match confirmed, photograph the old cover from the back and from above with the full row of upper clips in view. Send us a photograph of the label on the part you removed and we will match it before it ships.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e📦 Package Includes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e1 × DJI Talos T60X OEM Rear Cover of Rear Shell\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eOne moulded cover, supplied on its own.\u003c\/strong\u003e It is the outer cover of the rear shell only, not the Rear Shell Bottom Plate below it and not a complete rear shell.\u003c\/p\u003e\n\u003cp\u003eNot included: the Rear Shell Bottom Plate, any separate clips or clip receivers, screws, seals, decals, and anything mounted behind the cover. The clips visible along the cover's edges in the supplier photograph are part of the moulding as shown; compare them with the cover you removed.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🔧 Component Overview\u003c\/h2\u003e\n\u003cp\u003eThe rear cover of the rear shell is the outer skin across the rear of the T60X body. It is a wide, shallow, curved moulding, dark grey in the supplier photograph, with angled faces stepping down toward each end.\u003c\/p\u003e\n\u003cp\u003eIts most important features are on its edges. A row of clips and tabs runs along the upper edge, with a single tab near the centre, and smaller tabs sit along the lower edge. Those clips are how the cover is held: they engage the rear shell structure and, judging by its position, the area around the Rear Shell Bottom Plate. The exact engagement points on your aircraft are best read from the cover you removed and the shell it came off.\u003c\/p\u003e\n\u003cp\u003eWhat the cover is exposed to over a working season:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSpray drift and residue settling on the rear of the aircraft\u003c\/li\u003e\n\u003cli\u003ePressure washing at the end of the day, often aimed straight at its edges\u003c\/li\u003e\n\u003cli\u003eVibration from the propulsion system on every flight\u003c\/li\u003e\n\u003cli\u003eRemoval and refitting whenever the rear of the aircraft is opened for service\u003c\/li\u003e\n\u003cli\u003eKnocks from refill hoses, battery handling and loading at the rear\u003c\/li\u003e\n\u003cli\u003eSunlight on its exposed outer face\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe damage that ends its service is usually at the clips: a clip snapped off, a clip that has lost its spring and no longer grips, or a crack running from the root of a clip into the cover. A crack across the face, from a knock or a fall, is the other common cause.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e⚙️ Functional Purpose\u003c\/h2\u003e\n\u003cp\u003eThe cover's engineering role is to close the rear of the body and stay closed. It does that in four ways:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure\u003c\/strong\u003e — it closes the rear of the body shell so that what sits behind it is protected from spray, residue and wash water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProfile\u003c\/strong\u003e — its curve and stepped faces give the rear of the aircraft its outer shape\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRetention\u003c\/strong\u003e — its row of clips holds it against the rear shell without a long line of screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtection\u003c\/strong\u003e — as the outermost rear surface, it takes minor knocks during handling\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe cover has no electrical role. It carries no current and no signal, it has no connector, and the aircraft does not monitor it.\u003c\/p\u003e\n\u003cp\u003eWhat the rear cover does not do:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eIt does not repair a clip receiver or mounting on the rear shell that has broken\u003c\/li\u003e\n\u003cli\u003eIt does not replace the Rear Shell Bottom Plate\u003c\/li\u003e\n\u003cli\u003eIt does not straighten a rear shell or frame that has moved\u003c\/li\u003e\n\u003cli\u003eIt does not repair anything behind it damaged in the same event\u003c\/li\u003e\n\u003cli\u003eIt does not change any setting, calibration or firmware behaviour\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch2\u003e🔍 Diagnosis — a cover that will not stay seated may be the cover, or what it clips into\u003c\/h2\u003e\n\u003cp\u003eThe usual complaint is simple: the rear cover will not stay on. It pops off at one end, it lifts along the top edge in flight, or it will not click home at all. The natural conclusion is that the cover is broken, and a new cover is ordered.\u003c\/p\u003e\n\u003cp\u003eSometimes that is right. But a clip-held cover has two halves to every connection: the clip on the cover, and the edge, slot or receiver on the shell it clips into. When the receiver is cracked, worn or missing, or when the shell around it has moved, a perfect new cover fails in exactly the way the old one did. The symptom is identical from the outside. Only an inspection of both halves tells you which side has failed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCheck the cover:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWith the aircraft powered down and the battery removed, unclip the cover and lay it down with the clips facing up\u003c\/li\u003e\n\u003cli\u003eCount the clips along the upper edge and compare with the cover's other end; a missing clip is obvious once you look\u003c\/li\u003e\n\u003cli\u003eLook at the root of each clip for cracks or stress whitening\u003c\/li\u003e\n\u003cli\u003ePress each clip gently; a clip that has lost its spring stays where you push it\u003c\/li\u003e\n\u003cli\u003eLook across the face in raking light for cracks\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eThen check what it clips into:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLook at every slot, edge or receiver on the rear shell where a clip engages; cracks and broken corners are common here\u003c\/li\u003e\n\u003cli\u003eCheck the Rear Shell Bottom Plate along the cover's lower edge for cracks or a bow\u003c\/li\u003e\n\u003cli\u003eOffer the old cover back up and watch which clip fails to engage; then look at both halves of that one connection\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eReading the result:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eClips broken or soft on the cover, receivers sound — the cover is the fault, and this part fixes it\u003c\/li\u003e\n\u003cli\u003eClips sound on the cover, receivers cracked or missing — the shell is the fault, and a new cover will not stay on either\u003c\/li\u003e\n\u003cli\u003eBoth damaged — replace both, or the new cover will be loosened by the old receiver\u003c\/li\u003e\n\u003cli\u003eClips and receivers sound but the cover still lifts — check the bottom plate and the shell for distortion\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eDo these checks first, while that information is still cheap. A rear cover that will not seat is a question about two parts, and ordering only one of them is how a new cover ends up popping off on its first job.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e⚠️ Common Replacement Indicators\u003c\/h2\u003e\n\u003cp\u003eReplace the rear cover when inspection confirms one of these:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA snapped or missing clip or tab on the cover\u003c\/li\u003e\n\u003cli\u003eA clip that has lost its spring and no longer grips a sound receiver\u003c\/li\u003e\n\u003cli\u003eA crack starting at the root of a clip\u003c\/li\u003e\n\u003cli\u003eA crack anywhere across the face of the cover\u003c\/li\u003e\n\u003cli\u003eA cover that lifts or pops off when the receivers on the shell have been checked and are sound\u003c\/li\u003e\n\u003cli\u003eDistortion that stops the cover sitting evenly against a straight shell\u003c\/li\u003e\n\u003cli\u003ePrevious repairs with adhesive or tape holding a clip or crack\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInspect these as well, because they produce the same symptoms:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eEvery slot, edge or receiver on the rear shell that the clips engage\u003c\/li\u003e\n\u003cli\u003eThe Rear Shell Bottom Plate along the cover's lower edge\u003c\/li\u003e\n\u003cli\u003eThe rear shell structure behind the cover, after any knock to the rear of the aircraft\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThere is no published service interval for the rear cover. It is replaced when it is damaged.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e📐 Specifications\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eProduct name:\u003c\/strong\u003e DJI Talos T60X OEM Rear Cover of Rear Shell\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDJI family:\u003c\/strong\u003e Talos\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft:\u003c\/strong\u003e DJI Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFitment basis:\u003c\/strong\u003e Listed by the supplier for the Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVariant:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft system:\u003c\/strong\u003e Airframe — rear body shell, outer cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComponent type:\u003c\/strong\u003e Rear shell outer cover (single moulded cover)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuantity:\u003c\/strong\u003e 1 cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eColour:\u003c\/strong\u003e Dark grey, as shown in the supplier photograph\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVisible features:\u003c\/strong\u003e Wide shallow curved moulding, row of clips and tabs along the upper edge, a centre tab, angled faces stepping down toward each end, smaller tabs along the lower edge\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMounting position:\u003c\/strong\u003e Outer rear face of the T60X body shell; compare with the cover you removed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation method:\u003c\/strong\u003e Clip-on along its upper and lower edges; compare with the cover you removed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIncluded hardware:\u003c\/strong\u003e None separate — the clips shown are part of the moulding; separate receivers, screws and seals are not included\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial number:\u003c\/strong\u003e Not published for this part — send us a photograph of the label on the part you removed and we will match it before it ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eElectrical:\u003c\/strong\u003e None — a moulded shell part with no wiring, connector or electronics of its own\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eService adjustability:\u003c\/strong\u003e None — the part is correct and undamaged or it is not, with no adjustment or app setting that compensates\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCondition:\u003c\/strong\u003e Brand new\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eClassification:\u003c\/strong\u003e DJI OEM airframe shell component\u003c\/p\u003e\n\n\u003chr\u003e\n\u003ch2\u003e🛠️ Installation \u0026amp; Maintenance\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eBefore installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePower the aircraft down and remove the battery\u003c\/li\u003e\n\u003cli\u003eRinse and dry the rear of the aircraft so residue does not end up behind the cover\u003c\/li\u003e\n\u003cli\u003ePhotograph the rear of the aircraft with the cover in place, from behind and from above\u003c\/li\u003e\n\u003cli\u003eLay the new cover beside the old one and compare the outline, curvature and the number and position of clips\u003c\/li\u003e\n\u003cli\u003eInspect the receivers on the rear shell before the new cover goes on, using the checks in the Diagnosis section\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eDuring installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eUnclip the old cover working from one end along the clip row, without levering against the shell\u003c\/li\u003e\n\u003cli\u003eClean the receivers and seating edges on the rear shell\u003c\/li\u003e\n\u003cli\u003eLine the new cover up along its full length before pressing any clip home\u003c\/li\u003e\n\u003cli\u003eEngage the clips from the centre outward, pressing over each clip rather than on the open face of the cover\u003c\/li\u003e\n\u003cli\u003eStop if a clip needs force; look at that receiver before you push harder\u003c\/li\u003e\n\u003cli\u003eFit any screws where your aircraft uses them; DJI does not publish a torque figure for these fixings, so tighten evenly and stop when the cover is held\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eAfter installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRun a hand along the top edge; every clip should be engaged and the edge should sit evenly\u003c\/li\u003e\n\u003cli\u003ePress gently on the face; nothing should click, flex or lift\u003c\/li\u003e\n\u003cli\u003ePower up on the ground and confirm there are no warnings on the remote controller\u003c\/li\u003e\n\u003cli\u003eHover-test before a working flight and check the cover has not lifted at either end\u003c\/li\u003e\n\u003cli\u003eRecord the replacement, and the condition of the receivers, in the maintenance log\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eMaintenance between jobs.\u003c\/strong\u003e At wash-down, run a hand along the cover's top edge to feel for a clip that has started to lift, and avoid aiming the pressure washer straight into the clip line. Each time the cover comes off, unclip it in order rather than prising one end, so the clips are not bent past their spring.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🚜 Necessary For\u003c\/h2\u003e\n\u003cp\u003eThe rear cover is for operators and technicians closing up the rear of a Talos T60X:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTalos T60X operators whose rear cover has a broken clip or a cracked face\u003c\/li\u003e\n\u003cli\u003eCommercial spray and spreading contractors who open the rear of the aircraft often in the course of a season\u003c\/li\u003e\n\u003cli\u003eService centres and repair technicians rebuilding T60X rear shells\u003c\/li\u003e\n\u003cli\u003eFleet managers stocking a rear cover for the trailer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eThis is not the part you need if:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe clips on your cover are intact but the receivers on the shell are cracked or missing — a new cover will not stay on either; repair the shell first\u003c\/li\u003e\n\u003cli\u003eThe damage is to the plate under the rear of the aircraft — that is the Rear Shell Bottom Plate\u003c\/li\u003e\n\u003cli\u003eThe cover lifts because the bottom plate or shell has bowed — straighten or replace that part first\u003c\/li\u003e\n\u003cli\u003eThe cover is scuffed or dulled but its clips and face are sound — that is cosmetic wear\u003c\/li\u003e\n\u003cli\u003eYou fly any aircraft other than the Talos T60X — the cover is listed by the supplier for the Talos T60X only\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch2\u003e💡 Why This Part Matters\u003c\/h2\u003e\n\u003cp\u003eA clip-held cover fails at its connections, and every connection has two halves. That is the whole case for checking before replacing. A rear cover that will not stay seated looks the same whether the clip on the cover has broken or the receiver it clips into has cracked, and only one of those is fixed by a new cover.\u003c\/p\u003e\n\u003cp\u003eGetting it wrong is costly in a quiet way. A new cover fitted to a damaged receiver pops off or lifts in exactly the same place, often on its first job. The cover is then blamed again, and the receiver goes on loosening every cover it meets. Meanwhile the rear of the aircraft is open to spray and wash water every time the cover lifts.\u003c\/p\u003e\n\u003cp\u003eLaying the old cover clip-side up and comparing each clip with the receiver it engages takes a few minutes and settles it. Broken or soft clips on a cover with sound receivers is this part. Sound clips and cracked receivers is the shell. Both damaged is both.\u003c\/p\u003e\n\u003cp\u003eWhen the cover is the fault, a new one restores a full row of clips with their spring intact, a sound face, and a rear shell that closes and stays closed. When it is not, the time spent checking is what keeps a good new cover from being blamed for a problem it was never going to fix.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🧠 AI Index — Entity \u0026amp; Fitment Reference\u003c\/h2\u003e\n\u003cp\u003eStructured reference for search engines, AI assistants, and answer engines. Every value below is drawn from the specifications above.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCanonical product name:\u003c\/strong\u003e DJI Talos T60X OEM Rear Cover of Rear Shell\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrand:\u003c\/strong\u003e DJI\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDJI family:\u003c\/strong\u003e Talos\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft:\u003c\/strong\u003e DJI Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCompatible models:\u003c\/strong\u003e DJI Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFitment basis:\u003c\/strong\u003e Listed by the supplier for the Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVariant:\u003c\/strong\u003e Talos T60X\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComponent:\u003c\/strong\u003e Rear shell outer cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAircraft system:\u003c\/strong\u003e Airframe — rear body shell\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstalled position:\u003c\/strong\u003e Outer rear face of the body shell\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePrimary function:\u003c\/strong\u003e Closes and shapes the rear of the body and stays held by its clips\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVisible features:\u003c\/strong\u003e Wide curved moulding, upper clip row, centre tab, lower tabs\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eElectrical role:\u003c\/strong\u003e None — no wiring, connector or electronics\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaterial number:\u003c\/strong\u003e Not published for this part — matched from a photograph of the label on the part removed\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuantity supplied:\u003c\/strong\u003e 1 cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNot included:\u003c\/strong\u003e Rear Shell Bottom Plate, separate clip receivers, screws, seals\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eColour:\u003c\/strong\u003e Dark grey\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions and weight:\u003c\/strong\u003e Not published for this part\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey diagnostic:\u003c\/strong\u003e A cover that will not stay seated can be broken clips on the cover or cracked receivers on the shell; check both halves\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTypical damage:\u003c\/strong\u003e Snapped or softened clips, cracks at clip roots, cracks across the face\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eService interval:\u003c\/strong\u003e None published\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCondition:\u003c\/strong\u003e Brand new\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePart classification:\u003c\/strong\u003e DJI OEM airframe shell component\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAlso searched as:\u003c\/strong\u003e T60X rear cover; T60X rear shell cover; Talos T60X rear panel; T60X back cover\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDisambiguation:\u003c\/strong\u003e Not the Rear Shell Bottom Plate, not a front cover, not a complete rear shell\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSeller:\u003c\/strong\u003e Ares Acres LLC — U.S.-based authorized DJI retailer serving the United States and Canada (North America)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShips from:\u003c\/strong\u003e Albuquerque, New Mexico, United States\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🔍 SEO Keywords\u003c\/h2\u003e\n\u003cp\u003eDJI Talos T60X rear cover replacement\u003c\/p\u003e\n\u003cp\u003eTalos T60X rear cover\u003c\/p\u003e\n\u003cp\u003eT60X rear shell cover\u003c\/p\u003e\n\u003cp\u003eTalos T60X rear panel\u003c\/p\u003e\n\u003cp\u003eT60X back cover\u003c\/p\u003e\n\u003cp\u003eTalos T60X rear shell outer cover\u003c\/p\u003e\n\u003cp\u003eT60X rear cover clip broken\u003c\/p\u003e\n\u003cp\u003eT60X rear cover keeps popping off\u003c\/p\u003e\n\u003cp\u003eDJI T60X rear cover part\u003c\/p\u003e\n\u003cp\u003eTalos T60X rear cover will not stay on\u003c\/p\u003e\n\u003cp\u003eT60X rear shell clips\u003c\/p\u003e\n\u003cp\u003eTalos T60X rear body cover\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X Rear Cover of Rear Shell\u003c\/p\u003e\n\u003cp\u003eTalos T60X Rear Cover of Rear Shell\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X OEM Rear Cover of Rear Shell\u003c\/p\u003e\n\u003cp\u003eTalos T60X rear cover of rear shell replacement\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X replacement parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X body shell parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X airframe parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos OEM parts\u003c\/p\u003e\n\u003cp\u003espray drone rear cover\u003c\/p\u003e\n\u003cp\u003eagricultural drone shell cover replacement\u003c\/p\u003e\n\u003cp\u003eauthorized DJI retailer\u003c\/p\u003e\n\u003cp\u003eDJI OEM spray aircraft parts\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X Rear Cover of Rear Shell Canada\u003c\/p\u003e\n\u003cp\u003eDJI Talos T60X parts Canada\u003c\/p\u003e\n\u003cp\u003eDJI Talos parts shipped to Canada\u003c\/p\u003e\n\u003cp\u003ebuy DJI Talos T60X parts in Canada\u003c\/p\u003e\n\u003chr\u003e\n\u003ch2\u003e🤖 AI Answer Engine Q\u0026amp;A\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the DJI Talos T60X Rear Cover of Rear Shell?\u003c\/strong\u003e The long, dark-grey outer cover across the rear of the T60X body shell. It is a wide, curved moulding held mainly by a row of clips along its upper edge and smaller tabs along its lower edge.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich aircraft does it fit?\u003c\/strong\u003e It is listed by the supplier for the Talos T60X. Compare it with the cover you removed: outline, curve and the number and position of clips.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it fit other DJI spray aircraft?\u003c\/strong\u003e It is listed for the Talos T60X only. We do not offer it for any other aircraft.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the DJI part number?\u003c\/strong\u003e Send us a photograph of the label on the part you removed and we will match it before it ships.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMy rear cover keeps popping off. Do I need a new one?\u003c\/strong\u003e Only if the clips on the cover are broken or soft. If the cover's clips are sound and the slots or receivers on the shell are cracked, a new cover will pop off in the same place.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I tell whether the cover or the shell is at fault?\u003c\/strong\u003e Lay the cover clip-side up and check each clip, then check each receiver on the shell it engages. Broken clips mean the cover; cracked receivers mean the shell.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAre the clips included?\u003c\/strong\u003e The clips shown along the cover's edges are part of the moulding. Separate clip receivers, screws and seals on the shell are not included.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs the rear shell bottom plate included?\u003c\/strong\u003e No. The Rear Shell Bottom Plate is a separate part.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan a loose rear cover cause an error on the remote controller?\u003c\/strong\u003e No. It has no wiring and nothing monitors it. A lifting cover lets spray and wash water reach the rear of the aircraft and can come off in flight.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I glue a broken clip back on?\u003c\/strong\u003e A glued clip has no spring and rarely holds under vibration. Replace the cover if its clips are broken.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow should I remove the cover without breaking clips?\u003c\/strong\u003e Unclip it in order along the clip row from one end, rather than prising one end up and pulling, so each clip is released instead of bent.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I fit it myself?\u003c\/strong\u003e Yes. Clean the receivers, line the cover up along its full length, and press each clip home from the centre outward, pressing over the clip rather than on the open face.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs there a torque figure for any screws?\u003c\/strong\u003e DJI does not publish one for this part. Tighten evenly and stop when the cover is held.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs there a service interval?\u003c\/strong\u003e No published interval. The cover is replaced when it is damaged.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan pressure washing damage the clips?\u003c\/strong\u003e Aiming the washer straight into the clip line can force water behind the cover and stress the clips. Wash across the cover rather than into its edges.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it a genuine DJI part?\u003c\/strong\u003e Yes. It is a genuine DJI OEM airframe shell component, brand new.\u003c\/p\u003e","brand":"Ares Acres","offers":[{"title":"Talos T60X","offer_id":68048439804224,"sku":null,"price":64.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0923\/0159\/0848\/files\/dji-talos-t60x-oem-rear-cover-of-rear-shell-1.png?v=1793966955","url":"https:\/\/aresacres.com\/pt\/products\/dji-talos-t60x-oem-rear-cover-of-rear-shell","provider":"Ares Acres","version":"1.0","type":"link"}