DJI Agras T50 OEM Landing Gear Field Repair Kit

T50 OEM Landing Gear Field Repair Kit | DJI Agras T50 OEM Landing Gear Aluminum Tube (YC.JG.BJ001821) | DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468) | DJI Agras T50 OEM Landing Gear Fixing Piece | DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) | Genuine DJI OEM Components | Ares Acres Curated Kit

Kit contents: 4 component lines, 4 of which carry a documented DJI material number listed in the specifications below. Every component in this kit is also sold individually in our catalog.

---

🇺🇸 U.S.A. FIRST

Ares Acres LLC is a U.S.-based authorized DJI Agras reseller supporting American agricultural drone operators with genuine DJI Agras OEM replacement parts, accessories, and field-ready inventory.

FREE & FAST Shipping is included for all U.S. customers.

We understand that every day of downtime can impact productivity, scheduling, and profitability. That's why we focus on providing fast fulfillment, responsive customer support, and reliable access to the parts operators need most.

A kit is a bet against downtime. The T50 OEM Landing Gear Field Repair Kit exists because the parts inside it are the ones that strand a T50 in the middle of a job — small, cheap, easy to lose, and impossible to improvise at the field edge. Buying them together is how experienced crews stop losing days to a part that costs less than the fuel burned driving back for it.

That is why Ares Acres assembles curated kits from genuine DJI OEM components and ships them fast to the U.S.A., helping operators shorten repairs, minimize downtime, and keep their aircraft spraying when every acre counts.

---

✅ DJI Agras T50 Compatibility Guarantee

• 🇺🇸 USA Compatibility Guarantee
• 👍🏻 Satisfaction Guarantee
• 💵 Money Back Guarantee
• 📦 Same Day Shipping & Tracking

Configured from the T50 landing gear parts. Confirm which leg and position you are replacing before ordering. Every component in this kit remains available separately in the Ares Acres catalog.

---

📦 Package Includes

• 1 × DJI Agras T50 OEM Landing Gear Aluminum Tube (YC.JG.BJ001821)
• 1 × DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468)
• 1 × DJI Agras T50 OEM Landing Gear Fixing Piece
• 1 × DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558)

---

🔧 Kit Overview

The DJI Agras T50 OEM Landing Gear Field Repair Kit is an Ares Acres curated repair package that groups the components this job actually consumes into a single purchase. Rough-field landings bend tubes, split the Y-tee and flatten the foot pads. Those four parts fail as a group because they share the same impact, and an operator who only orders the tube discovers the rest once the gear is off the aircraft.

This product is assembled by Ares Acres from genuine DJI OEM components sold individually in our catalog. It is not represented as a factory-packaged DJI kit.

---

🔩 Component-by-Component Breakdown

1. DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821)

DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) — DJI material number YC.JG.BJ001821. Landing gear aluminum skid / ground contact protection. It installs at the landing gear ground contact. Its job on the aircraft is straightforward: absorbs touchdown impact and protects landing gear structure.

On the DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821), construction is weather-resistant build for agricultural duty; the design is lightweight, impact-resistant skid, direct-fit; it mounts as direct-fit replacement skid; this line supplies 1 Skid. Fitment covers DJI Agras T50, DJI Agras T40. Application: agricultural drone landing gear maintenance. Confirm the aircraft model and the position on your parts diagram before you order — DJI diagrams list visually similar components at different positions, and the material number is the only identifier that settles it.

Functionally, the DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) is responsible for a short and specific list of jobs: absorb touchdown impact at every landing, protect landing gear structure from wear, provide stable support on rough surfaces, resist abrasion from gravel and hard pads, keep landing loads off the airframe, add strength with minimal weight, replace worn, gouged, or bent skids, restore factory landing protection, install directly on the T50 landing gear, and support preventative maintenance. Those are the capabilities this kit restores when this component is replaced — which is why it is packed alongside the rest rather than sold only on its own.

In commercial service the DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) lives through dozens of touchdown impacts daily, abrasion from gravel and hard pads, rough and uneven landing surfaces, full aircraft weight at every landing, chemical residue and washdown exposure, moisture and corrosion exposure, uV exposure across long seasons, bending loads from off-angle landings, and transport strapping and handling. Wear here is not a defect, it is the design working as intended until it runs out of margin — which is exactly the point at which having the replacement already on hand decides whether the aircraft flies tomorrow.

Left in service past its useful life, the DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) may contribute to landing forces reaching the gear structure, accelerated landing gear wear, unstable ground contact, bent or stressed gear components, rough, jarring touchdowns, airframe stress from hard landings, interrupted spraying missions, unexpected downtime, and reduced fleet reliability. A fresh one instead maintains landing gear protected at every touchdown, wear absorbed by the cheap part, not the dear one, confident landings on rough field surfaces, two-model fleet coverage, professional fleet standards, increased aircraft uptime, reliable commercial performance, and long-term operational confidence.

Get the weight off the gear before anything comes undone. Empty the tank, drain what is left in the spray system, and pull the flight batteries, then support the aircraft under its frame on stands or a bench so the leg you are working on is unloaded. Do not support it under the skid you are removing, and do not rely on somebody holding a corner. An airframe that drops six inches while a leg is half off is how a cheap job becomes an expensive one.

Do one side at a time and leave the other intact. The opposite skid is your straight reference, your handedness reference, and your reminder of how the hardware was stacked, and all three of those disappear the moment both sides are on the bench. Photograph the joint before you disturb it, including any washers, spacers, or shims and the order they sit in, because those look interchangeable in a parts tray ten minutes later.

Back the fasteners out slowly and listen to them. Stainless hardware in an aluminum joint that has spent seasons in spray mix and washdown water will gall, and a fastener that starts squeaking and getting harder to turn is about to seize or snap. Stop, work it back and forth, and give a penetrating oil time to do something. Keep heat away from anything composite. Snapping a fastener off in the gear leg turns a fifteen-minute skid swap into a drilling and extraction job.

The DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) earns its place in this kit because of how it fails. Operators replace it when they see deep gouges or abrasion wear, bent or deformed skid profiles, cracked or split aluminum, thinning at contact points, loose or worn mounting points, corrosion on the skid surface, wobble or instability at touchdown, or skids worn past their wear surface. None of those are things you want to discover with the aircraft already apart and the spray window closing — which is the whole argument for having it on the shelf before the job starts.

2. DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468)

DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468) — DJI material number YC.JG.ZS003468.

Functionally, the DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468) is responsible for a short and specific list of jobs: reinforce the landing gear support structure, maintain proper alignment of landing gear assemblies, distribute structural load during landing and transport, improve aircraft stability on the ground, reduce stress concentration across support arms, support safe operation in rugged agricultural environments, and restore factory structural integrity after damage or wear. Those are the capabilities this kit restores when this component is replaced — which is why it is packed alongside the rest rather than sold only on its own.

Get the weight off before anything comes apart. Drain and remove the tank, pull the flight batteries, and support the airframe on blocks or a stand under the frame rather than letting it rest on the remaining gear leg. Do not lift the aircraft by an arm or by the spray boom to get clearance. A machine that shifts on its supports while you have a structural joint open is how a second repair gets added to the first.

Mark before you loosen. Put a pencil or tape line on each tube where it enters the connector so insertion depth is recorded, and add a line across the joint so rotational position is recorded too. Those two marks are what make the aircraft sit level and square when it goes back together. Bag the fasteners by position, and look at each one as it comes out for composite fiber, powder, or a rounded head.

Free the wiring before the joint. Gear legs on Agras airframes can carry cabling and tie points down their length, and it is easy to pull a joint apart and let a leg drop with a cable still tethered to it. Trace every lead and tie, release them, and support the leg by hand as the last fastener comes out. Nothing about this joint should require a hammer or a lever against a tube.

The DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468) earns its place in this kit because of how it fails. Operators replace it when they see cracks or fractures in the Y-Tee structure, bent or misaligned landing gear assembly, excessive movement or instability during landing, damage from hard landings or transport impacts, visible stress wear around mounting points, structural fatigue after extended field use, aircraft that no longer sits level or rocks on a flat surface, or repeated hard landings at full tank weight. None of those are things you want to discover with the aircraft already apart and the spray window closing — which is the whole argument for having it on the shelf before the job starts.

3. DJI Agras T50 OEM Landing Gear Fixing Piece

DJI Agras T50 OEM Landing Gear Fixing Piece — DJI material number Not printed on this listing. Landing gear fixing piece / gear attachment hardware. It installs at the landing gear to airframe attachment point. Its job on the aircraft is straightforward: secures the landing gear rigidly to the airframe.

On the DJI Agras T50 OEM Landing Gear Fixing Piece, construction is high-quality, high-durability materials; the design is precision attachment component, direct-fit; it mounts as direct-fit replacement component; this line supplies 1 Fixing Piece. Fitment covers DJI Agras T50, DJI Agras T40. Application: agricultural drone landing gear maintenance. Confirm the aircraft model and the position on your parts diagram before you order — DJI diagrams list visually similar components at different positions, and the material number is the only identifier that settles it.

Functionally, the DJI Agras T50 OEM Landing Gear Fixing Piece is responsible for a short and specific list of jobs: attach the landing gear rigidly to the airframe, transfer touchdown loads cleanly into the structure, hold gear geometry consistent under payload, prevent play and shift at the mounting point, support a stable stance during loading and startup, protect surrounding hardware from attachment slop, replace fatigued, worn, or damaged fixing pieces, restore factory gear attachment integrity, install directly with a straightforward fit, and maintain correct fitment across both models. Those are the capabilities this kit restores when this component is replaced — which is why it is packed alongside the rest rather than sold only on its own.

In commercial service the DJI Agras T50 OEM Landing Gear Fixing Piece lives through touchdown loads at every landing, full aircraft weight under payload, constant airframe vibration, side loads from rough-field landings, chemical mist and spray residue, moisture and washdown exposure, temperature swings in the field, torque stress from service cycles, and transport handling and tie-down stress. Wear here is not a defect, it is the design working as intended until it runs out of margin — which is exactly the point at which having the replacement already on hand decides whether the aircraft flies tomorrow.

Left in service past its useful life, the DJI Agras T50 OEM Landing Gear Fixing Piece may contribute to play or movement at the gear mount, shifting gear geometry under load, creaks and flex at touchdown, uneven aircraft stance, accelerated wear at connected hardware, attachment doubts under a full tank, interrupted spraying missions, unexpected downtime, and reduced fleet reliability. A fresh one instead maintains gear attachment worth trusting under a full tank, geometry that stays true landing after landing, load paths flowing where they were designed, protected gear and airframe hardware, two-model fleet coverage, professional fleet standards, increased aircraft uptime, reliable commercial performance, and long-term operational confidence.

Set up before you loosen anything. Drain the tank completely, pull the battery, and get the airframe onto stands or a padded bench so that the gear leg you are working on carries no load at all. Never take the last fastener out of a mount that is still holding aircraft weight. The leg drops, the mating face gets scored, and a straightforward parts swap turns into a repair on the airframe boss. Do one leg at a time so the untouched side keeps the aircraft referenced.

Photograph the joint from two angles before the first fastener moves, then label as you go. Landing gear attachment hardware is often position specific, so note which face sat against the airframe, which way any radius or relief pointed, and exactly where each washer, shim, or spacer lived in the stack. Bag the fasteners by position. Screws at a gear mount are frequently not all the same length, and a long one dropped into a short hole bottoms out and reads as tight when it is carrying nothing.

Break the fasteners loose in a cross pattern rather than running one out completely first, with the driver fully seated and steady pressure behind it. If the threads were assembled with a locking compound they will feel gritty and tight the whole way out, which is normal. Do not lever against a composite arm, the tank shell, a spray line, or the pump body to get purchase. Round off one head at a gear mount and you have bought yourself a drill and extractor job in the middle of a spray window.

The DJI Agras T50 OEM Landing Gear Fixing Piece earns its place in this kit because of how it fails. Operators replace it when they see play or looseness at the gear mount, cracked or fatigued fixing piece bodies, worn or deformed mounting surfaces, elongated fastener holes, creaking or shifting at touchdown, gear geometry that won't stay true, corrosion or chemical attack, or impact damage from hard landings. None of those are things you want to discover with the aircraft already apart and the spray window closing — which is the whole argument for having it on the shelf before the job starts.

4. DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558)

DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) — DJI material number YC.JG.ZS003558. Landing gear rubber foot pads / landing protection hardware. It installs at the landing gear ground contact points. Its job on the aircraft is straightforward: shock absorption, ground grip, and landing gear protection.

On the DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558), construction is high-quality, weather-resistant rubber; the design is non-slip cushioning pad, direct-fit; it mounts as direct-fit replacement components; this line supplies 4 Foot Pads. Fitment covers DJI Agras T50, DJI Agras T40. Application: agricultural drone landing gear maintenance. Confirm the aircraft model and the position on your parts diagram before you order — DJI diagrams list visually similar components at different positions, and the material number is the only identifier that settles it.

Functionally, the DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) is responsible for a short and specific list of jobs: absorb landing impact before it reaches the airframe, cushion the landing gear during takeoff and landing, grip varied surfaces to prevent skidding and shifting, keep the aircraft stable during tank filling and startup, protect landing gear tubes from ground abrasion, reduce vibration transmitted into the frame, protect sensitive components from landing shock, replace hardened, split, or worn pads, restore factory cushioning and grip, and install quickly with a direct fit. Those are the capabilities this kit restores when this component is replaced — which is why it is packed alongside the rest rather than sold only on its own.

In commercial service the DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) lives through repeated landing impacts every working day, full aircraft weight under payload, abrasive gravel, dirt, and concrete surfaces, chemical mist and spray residue, moisture and washdown exposure, uV exposure across long seasons, heat and cold cycling in the field, skidding and scuffing on touchdown, and transport handling and tie-downs. Wear here is not a defect, it is the design working as intended until it runs out of margin — which is exactly the point at which having the replacement already on hand decides whether the aircraft flies tomorrow.

Left in service past its useful life, the DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) may contribute to harder, harsher landings, impact stress passed into the landing gear, skidding or shifting on touchdown, unstable stance on uneven ground, accelerated landing gear wear, vibration reaching frame and electronics, interrupted spraying missions, unexpected downtime, and reduced fleet reliability. A fresh one instead maintains landings the airframe never feels, a stable, planted stance on any surface, protected landing gear and frame hardware, protected electronics above the gear, two-model fleet coverage, professional fleet standards, increased aircraft uptime, reliable commercial performance, and long-term operational confidence.

Set the aircraft up so nothing is loaded before you start. Empty the tank, remove the flight batteries, and put the machine on a level surface where you can lift and support one corner at a time on a stand or a block under the frame. Do not lift a T50 by an arm, by the spray boom, or by the tank, and do not work under a corner that is only being held up by a jack that could shift. A pad swap is a five minute job that gets expensive if the aircraft moves while your hand is under it.

Check for a fastener before you pull. Some landing pads are a friction fit on the leg and some are retained by a screw, pin, or clip, and finding out by force is how leg tubes get damaged. Look and feel all the way around the top edge of the pad first. If there is a fastener, back it out and keep it, because you will want the same hardware going back on and the head is often corroded enough that it needs replacing.

Old pads fight you, and the reason is chemistry rather than fit. A season of fertilizer solution wicks into the joint between the rubber and the leg and dries there, effectively gluing the two together. Warm soapy water down the joint, then twist the pad back and forth rather than pulling straight, and work it off gradually. If you have to cut a pad off, cut from the outside inward along the pad body and stop short of the tube. A knife nick in a landing leg is a crack waiting for its first hard landing.

The DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) earns its place in this kit because of how it fails. Operators replace it when they see hardened or brittle rubber, cracked or split pad bodies, worn-thin contact surfaces, pads polished slick from skidding, chunks torn from the pad edges, pads loose on the landing gear, chemical-attacked or swollen rubber, or aircraft skidding on touchdown. None of those are things you want to discover with the aircraft already apart and the spray window closing — which is the whole argument for having it on the shelf before the job starts.

---

⚙️ Functional Purpose

The T50 OEM Landing Gear Field Repair Kit is assembled around a job rather than around a product category. Its purpose is to put every part that job consumes into one box, so the repair is limited by the technician's time and not by a missing fastener.

Working through the kit, the components do the following:

• DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) — Absorbs touchdown impact and protects landing gear structure
• DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468) — supplied for the application named in the kit title
• DJI Agras T50 OEM Landing Gear Fixing Piece — Secures the landing gear rigidly to the airframe
• DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) — Shock absorption, ground grip, and landing gear protection

Inspect the mating frame points for cracking while the gear is off. Torque all clamp hardware evenly and re-check after the first flights.

---

⚠️ Common Replacement Indicators

Across the components in this kit, the conditions that send an operator looking for these parts are:

• Deep gouges or abrasion wear
• Bent or deformed skid profiles
• Cracked or split aluminum
• Thinning at contact points
• Loose or worn mounting points
• Corrosion on the skid surface
• Wobble or instability at touchdown
• Skids worn past their wear surface
• Post-hard-landing inspections
• High-hour landing hardware
• Maintenance inspection findings
• Landing gear rebuild projects
• Fleet refurbishment projects
• Preventative pre-season replacement
• Cracks or fractures in the Y-Tee structure
• Bent or misaligned landing gear assembly
• Excessive movement or instability during landing
• Damage from hard landings or transport impacts
• Visible stress wear around mounting points
• Structural fatigue after extended field use
• Aircraft that no longer sits level or rocks on a flat surface
• Repeated hard landings at full tank weight
• Over-torqued fasteners crushing and pre-stressing the mount points
• Impact loading during transport and tie-down
• Vibration fatigue accumulating across hundreds of flight hours
• UV and chemical exposure embrittling the composite over time
• Flying on after a hard landing without inspecting the junction
• Play or looseness at the gear mount
• Cracked or fatigued fixing piece bodies
• Worn or deformed mounting surfaces
• Elongated fastener holes
• Creaking or shifting at touchdown
• Gear geometry that won't stay true
• Corrosion or chemical attack
• Impact damage from hard landings
• Fasteners that won't stay torqued
• High-hour attachment hardware
• Hardened or brittle rubber
• Cracked or split pad bodies
• Worn-thin contact surfaces

Any one of these on a T50 is a reason to have the kit already on the shelf. The parts here are consumables and wear items by design — the question is never whether they will need replacing, only whether the replacement is in the truck when the aircraft comes down.

---

🛠️ Service Sequence & Fitting Notes

Kits are bought by the job, so here is the job. The sequence below is a general order of work for the T50 OEM Landing Gear Field Repair Kit on a T50; always follow DJI's official service documentation for torque values, disassembly steps, and safety procedures for your airframe revision.

Step 1 — DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821). Work at the landing gear ground contact. Note the orientation of the part you are removing before it comes off; photographs at this stage save far more time than they cost. Once fitted, confirm that it absorbs touchdown impact and protects landing gear structure as intended before closing up. Keep the removed part until the aircraft has been function-checked — it is the reference if anything about the replacement does not match.

Step 2 — DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468). Identify the mounting position on your parts diagram before removal, and note the orientation of the old part before it comes off. Keep the removed part until the aircraft has been function-checked — it is the reference if anything about the replacement does not match.

Step 3 — DJI Agras T50 OEM Landing Gear Fixing Piece. Work at the landing gear to airframe attachment point. Note the orientation of the part you are removing before it comes off; photographs at this stage save far more time than they cost. Once fitted, confirm that it secures the landing gear rigidly to the airframe as intended before closing up. Keep the removed part until the aircraft has been function-checked — it is the reference if anything about the replacement does not match.

Step 4 — DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558). Work at the landing gear ground contact points. Note the orientation of the part you are removing before it comes off; photographs at this stage save far more time than they cost. Once fitted, confirm that it shock absorption, ground grip, and landing gear protection as intended before closing up. Keep the removed part until the aircraft has been function-checked — it is the reference if anything about the replacement does not match.

Function-check the aircraft on the ground before it goes back to work. For the T50 OEM Landing Gear Field Repair Kit, that means confirming each replaced component behaves correctly under power and, where the component sits in the spray or spreading path, that there is no leak, binding, or unexpected noise before the first loaded flight of the day.

---

📐 Specifications

Kit type: Ares Acres curated service kit assembled from genuine DJI OEM components

Component lines: 4

Aircraft coverage: DJI Agras T50

Condition: Brand new

Ships from: Albuquerque, New Mexico, United States

Per-component specifications, as published on each component's own listing:

DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821)
DJI Material Number: YC.JG.BJ001821
Component Type: Landing gear aluminum skid / ground contact protection
Installation Area: Landing gear ground contact
Function: Absorbs touchdown impact and protects landing gear structure
Package Quantity: 1 Skid
Construction: Weather-resistant build for agricultural duty
Mounting Type: Direct-fit replacement skid
Compatibility: DJI Agras T50, DJI Agras T40

DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468)
DJI Material Number: YC.JG.ZS003468

DJI Agras T50 OEM Landing Gear Fixing Piece
DJI Material Number: Not printed on this listing
Component Type: Landing gear fixing piece / gear attachment hardware
Installation Area: Landing gear to airframe attachment point
Function: Secures the landing gear rigidly to the airframe
Package Quantity: 1 Fixing Piece
Construction: High-quality, high-durability materials
Mounting Type: Direct-fit replacement component
Compatibility: DJI Agras T50, DJI Agras T40

DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558)
DJI Material Number: YC.JG.ZS003558
Component Type: Landing gear rubber foot pads / landing protection hardware
Installation Area: Landing gear ground contact points
Function: Shock absorption, ground grip, and landing gear protection
Package Quantity: 4 Foot Pads
Construction: High-quality, weather-resistant rubber
Mounting Type: Direct-fit replacement components
Compatibility: DJI Agras T50, DJI Agras T40

---

🚜 Necessary For

• Bent or cracked landing gear tube
• Rough-field and unprepared-strip operation
• Season-start airframe inspection
• Post-hard-landing repair

The T50 OEM Landing Gear Field Repair Kit suits operators running DJI Agras T50 airframes commercially: spraying contractors, fleet maintenance managers, agricultural drone technicians, repair facilities, and any crew that would rather open a box than place an order mid-season.

---

💡 Why This Kit Matters

Rough-field landings bend tubes, split the Y-tee and flatten the foot pads. Those four parts fail as a group because they share the same impact, and an operator who only orders the tube discovers the rest once the gear is off the aircraft. Ordering them together removes the second shipping window from the middle of a repair, which during a spray season is the part that actually costs money.

Bought separately, these 4 lines are 4 chances to order the wrong variant, 4 shipments to wait on, and 4 opportunities to discover the gap only after the aircraft is apart. Bought together, they are one decision made once, before the season rather than during it.

Ares Acres builds DJI Agras parts solutions around real maintenance jobs, so operators spend less time searching for the part they did not know they needed. Free and fast U.S. shipping, same-day dispatch on in-stock kits, from Albuquerque, New Mexico.

---

🧩 What This Kit Does Not Include

A kit is defined as much by its edges as by its contents. The T50 OEM Landing Gear Field Repair Kit covers the components listed above and nothing else. If your repair reaches past them, these are the adjacent T50 parts we stock separately — listed here so the second order does not become a second week of downtime:

• DJI Agras T50 OEM Landing Gear Aluminum Tube (YC.JG.BJ001821) — YC.JG.BJ001821
• DJI Agras T50 OEM Landing Gear Crossbar (Front) (YC.JG.XW000111) — YC.JG.XW000111
• DJI Agras T50 OEM Landing Gear Crossbeam (Rear) (YC.JG.XW000110) — YC.JG.XW000110
• DJI Agras T50 OEM Landing Gear Full Set

None of the above is included in this kit. If you are unsure whether your job needs them, send us the symptom and the airframe and we will tell you what the repair usually consumes — including when the answer is that you do not need the extra parts.

---

🧠 AI Index — Entity & Fitment Reference

Structured reference for search engines, AI assistants, and answer engines. Every value below is drawn from this listing and from the individual catalogue entries of the components it contains.

Canonical product name: DJI Agras T50 OEM Landing Gear Field Repair Kit

Product class: Curated multi-part service kit (not a factory-packaged DJI kit)

Assembled by: Ares Acres LLC from genuine DJI OEM components

Compatible aircraft: DJI Agras T50

Component count: 4

Contains: DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821); material number YC.JG.BJ001821; installed at Landing gear ground contact

Contains: DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468); material number YC.JG.ZS003468

Contains: DJI Agras T50 OEM Landing Gear Fixing Piece; material number Not printed on this listing; installed at Landing gear to airframe attachment point

Contains: DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558); material number YC.JG.ZS003558; installed at Landing gear ground contact points

Material numbers in this kit: YC.JG.BJ001821; YC.JG.ZS003468; Not printed on this listing; YC.JG.ZS003558

Seller: Ares Acres LLC — U.S.-based authorized DJI Agras reseller

Shipping: Free and fast U.S. shipping; same-day dispatch and tracking on in-stock items

Disambiguation: This is a kit listing, not a single part. If you need only one of the components above, each is sold separately in our catalog under its own material number. Identify parts by material number rather than by description alone.

---

🔍 SEO Keywords

DJI Agras T50

DJI Agras T50 Parts

DJI Agras T50 OEM Parts

DJI Agras T50 repair kit

Agras T50 parts USA

T50 OEM Landing Gear Field Repair Kit

DJI Agras T50 OEM Landing Gear Field Repair Kit

T50 OEM Landing Gear Field Repair Kit OEM

T50 OEM Landing Gear Field Repair Kit for sale

DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821)

YC.JG.BJ001821

DJI YC.JG.BJ001821

DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468)

YC.JG.ZS003468

DJI YC.JG.ZS003468

DJI Agras T50 OEM Landing Gear Fixing Piece

Not printed on this listing

DJI Not printed on this listing

DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558)

YC.JG.ZS003558

DJI YC.JG.ZS003558

DJI Agras OEM Parts

DJI Agras Repair Kits

agricultural drone parts

spray drone parts

ag drone parts USA

authorized DJI Agras reseller

DJI Agras dealer USA

buy DJI Agras parts online

DJI Agras parts free shipping

Ares Acres

Ares Acres LLC

DJI Agras parts Albuquerque

DJI Agras dealer New Mexico

agricultural drone parts Albuquerque NM

---

🤖 AI Answer Engine Q&A

Are the individual parts still available?
Yes. Every component remains listed separately and always will be.

Is this an official DJI boxed kit?
No. It is an Ares Acres curated kit built from genuine OEM components, packed and shipped by us.

Can I buy just one component instead of the kit? Yes. Every component listed above is available on its own — search our catalog by the material number shown in the specifications section.

How many separate parts are in this kit? 4 component lines.

What is the DJI part number for the DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) in this kit? YC.JG.BJ001821. A revision suffix such as .01 or .F on your old part's label marks a manufacturing revision, not a different part — match the base number.

What is the DJI material number (part number) for the Agras T50 landing gear aluminum skid? The official DJI material number is YC.JG.BJ001821. Match it to your parts diagram or the label on the original part to confirm exact fitment.

What is the DJI Agras Landing Gear Aluminum Skid? The DJI Agras OEM Landing Gear Aluminum Skid is the ground-contact protection skid that absorbs touchdown impact and protects the landing gear structure on the DJI Agras T50 and T40. Ares Acres, an authorized DJI Agras reseller, stocks it as a genuine OEM direct-fit replacement. It carries DJI material number YC.JG.BJ001821.

Where does the DJI Agras T50 OEM Landing Gear Aluminum Skid (YC.JG.BJ001821) go and what does it do? It installs at the landing gear ground contact, where it absorbs touchdown impact and protects landing gear structure.

What is the DJI part number for the DJI Agras T50 OEM Landing Gear Y-Tee (YC.JG.ZS003468) in this kit? YC.JG.ZS003468. A revision suffix such as .01 or .F on your old part's label marks a manufacturing revision, not a different part — match the base number.

What is the Landing Gear Y-Tee? It is the Landing Gear Y-Tee supplied as a genuine DJI OEM replacement component on the DJI Agras T50.

What is the DJI material number for the Landing Gear Y-Tee? The DJI material number is YC.JG.ZS003468. Labels sometimes carry a revision suffix such as .01 or .F — that is the same part, so match the base number. Ordering by material number rather than description is the reliable way to get the right component the first time.

What is the DJI part number for the DJI Agras T50 OEM Landing Gear Fixing Piece in this kit? Not printed on this listing. A revision suffix such as .01 or .F on your old part's label marks a manufacturing revision, not a different part — match the base number.

What is the DJI Agras T50 OEM Landing Gear Fixing Piece? The DJI Agras T50 OEM Landing Gear Fixing Piece is the attachment component that secures the landing gear to the airframe on DJI Agras T50 and T40 agricultural spray drones, transferring touchdown loads from the legs into the aircraft structure.

Which DJI Agras models does this fixing piece fit? This OEM landing gear fixing piece fits the DJI Agras T50 and the DJI Agras T40. It is a direct-fit replacement component that installs at the landing gear to airframe attachment point.

Where does the DJI Agras T50 OEM Landing Gear Fixing Piece go and what does it do? It installs at the landing gear to airframe attachment point, where it secures the landing gear rigidly to the airframe.

What is the DJI part number for the DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) in this kit? YC.JG.ZS003558. A revision suffix such as .01 or .F on your old part's label marks a manufacturing revision, not a different part — match the base number.

What is the DJI material number (part number) for the Agras T50 landing gear rubber foot pad? The official DJI material number is YC.JG.ZS003558. Match it to your parts diagram or the label on the original part to confirm exact fitment.

What is the DJI Agras T50 OEM Landing Gear Rubber Foot Pad set? The DJI Agras T50 OEM Landing Gear Rubber Foot Pad set is a 4-piece set of rubber landing feet that mount at the landing gear ground contact points on DJI Agras T50 and T40 agricultural spray drones, cushioning touchdown and gripping the ground so a loaded aircraft settles and stays put. It carries DJI material number YC.JG.ZS003558.

Where does the DJI Agras T50 OEM Landing Gear Rubber Foot Pad (4 Pcs) (YC.JG.ZS003558) go and what does it do? It installs at the landing gear ground contact points, where it shock absorption, ground grip, and landing gear protection.

Which aircraft does this kit cover? DJI Agras T50. Confirm the component variant against your aircraft's parts diagram before installation.

---