Skip to product information
1 of 1

XAG

XAG P150 OEM Application System Tube Connector Component

XAG P150 OEM Application System Tube Connector Component

Regular price $75.99 USD
Regular price Sale price $75.99 USD
Sale Sold out
Shipping calculated at checkout.

Live Representative Assistant · Secure payment

Add multiple parts or continue shopping
Secure Checkout
Encrypted · Trusted Processors · Buyer Protection
30-Day Money-Back Guarantee
Order with confidence · Hassle-free returns
Same-Day Shipping + Tracking
Same Day Shipping · Same Day Tracking
#1 US DJI Agras Parts Specialist
DJI OEM parts · For US Pilots

The XAG P150 OEM Application System Tube Connector Component, XAG part number 14-007-00116, is a tube connector component in the application system of the XAG P150 (2024) agricultural drone. It joins tubes in the liquid path so that product flows from tank to nozzles without leaking. Leaks at joints are usually obvious: drips and wet residue. But a joint on the suction side of a pump can fail in a less obvious way, drawing air in instead of letting liquid out, which shows up as poor priming, surging flow or uneven spraying with no drip to be seen. Operators reach it through searches such as P150 tube connector, XAG P150 spray tube fitting, P150 application system leak, or XAG P150 pump not priming.


🇺🇸 U.S.A. FIRST

Ares Acres is an agricultural technology retailer distributing OEM XAG parts. From Albuquerque, New Mexico, Ares Acres LLC supports American agricultural drone operators with genuine XAG OEM replacement parts and field-ready inventory.

FREE & FAST Shipping is included for all U.S. customers.

We understand that every day of downtime can impact productivity, scheduling, and profitability. That's why we focus on providing fast fulfillment, responsive customer support, and reliable access to the parts operators need most.

Ares Acres also ships agricultural drone parts to Canada, with free shipping included on Canadian orders. Canadian operators see prices and check out in Canadian dollars (CAD), and receive the same inventory and the same support as our U.S. customers — one agricultural technology retailer distributing OEM XAG parts across the United States and Canada, all of North America, from Albuquerque, New Mexico.


✅ XAG P150 Compatibility Guarantee

  • 🇺🇸 USA Compatibility Guarantee
  • 👍🏻 Satisfaction Guarantee
  • 💵 Money Back Guarantee
  • 📦 Same Day Shipping & Tracking
  • Fitted in the application system liquid path of the XAG P150 (2024); not confirmed for the P150 Max
  • Matched by XAG part number 14-007-00116 and by size and form against the connector you removed
  • Genuine XAG OEM tube connector component, brand new

📦 Package Includes

  • 1 × XAG P150 application system tube connector component, XAG part number 14-007-00116
  • The component as XAG supplies it under this part number
  • OEM protective packaging

Not included: the application system tubes, including the long tube (02-002-14300) and short tube (02-002-14301); the pump; the water pipe adapter (14-007-00019); or tools.


🔧 Component Overview

The liquid path of the P150's application system runs from the tank, through the pump, through tubes and connectors, to the nozzles. Every joint along that path is a place where liquid could escape or air could enter. Tube connector components make those joints, joining tubes securely and sealing them so that the system holds pressure and delivers exactly what the operator has set.

On the pressure side of the pump, the side that pushes liquid toward the nozzles, a failing joint leaks outward. Drips, wet residue and stains around the joint make it easy to find. Those leaks waste product, contaminate the airframe and can reach electronics.

On the suction side of the pump, the side that draws liquid from the tank, a failing joint behaves differently. The pump is pulling, so a poor seal draws air in rather than letting liquid out. There may be no drip at all. Instead, the pump struggles to prime, the flow surges or pulses, bubbles appear in clear sections of tube, and spraying becomes uneven. It is easy to blame the pump or the nozzles for symptoms that actually come from an air leak at a connector.

The specific position of this connector in the P150 liquid path is not published for this part. Wherever it sits, the same principles apply: a joint must be fully seated, square and sealed, and the connector must be undamaged.

Connectors fail from cracks caused by impacts and over-tightening, from chemical attack on the connector or its seals, from repeated disconnection during cleaning and changeover, and from tubes pulled at an angle that stress the joint. Dried residue can also stop a connector seating fully.

A simple test finds most problems. Run the system with clean water and watch every joint for drips. Then watch the flow: steady flow and a quick prime suggest a sound suction side; surging, slow priming and bubbles suggest air is getting in somewhere.

When a connector is replaced, the tube ends it joins should be inspected too. A split or hardened tube end will not seal even in a new connector.

Where it sits. In the application system liquid path; specific position not published for this part.

What it connects to. The application system tubes it joins.

What wears it out. Chemical attack. Repeated disconnection. Over-tightening. Impacts. Tubes pulled at an angle. Dried residue.

What this part is not. It is not a tube, the pump or the water pipe adapter.


⚙️ Functional Purpose

The application system tube connector component joins tubes in the liquid path and seals the joint.

A sound tube connector provides:

  • A secure joint between application system tubes
  • A seal that holds liquid in on the pressure side
  • A seal that keeps air out on the suction side
  • Steady flow and reliable priming
  • Accurate delivery of the set application rate

Its value is in keeping product in the system and air out of it.


🔍 Diagnosis — poor priming or surging flow with no drip: look for an air leak at a joint

Not every leak drips. On the suction side, a failing joint draws air in. Check connectors when flow is uneven, even if everything looks dry.

  • Remove the battery for inspection. Confirm the aircraft cannot be powered while handling parts.
  • Run a water test. Fill with clean water and run the system as directed by the aircraft's procedures.
  • Watch for drips. Wet joints and residue stains show outward leaks.
  • Watch the flow. Slow priming, surging or pulsing flow suggests air is getting in.
  • Look for bubbles. Bubbles in clear tube sections point at an air leak upstream.
  • Inspect each connector. Look for cracks, incomplete seating and damaged seals.
  • Inspect the tube ends. Split or hardened tube ends will not seal.
  • Photograph the damage. Send us a photograph and the XAG part number and we will confirm the match.

If the connector is cracked, will not seat fully, or leaks liquid or air after reseating, this connector is the part.


⚠️ Common Replacement Indicators

Tube connector replacement is the likely answer when an operator or technician observes:

  • Drips or wet residue at a joint
  • Slow priming or a pump that loses prime
  • Surging or pulsing flow
  • Bubbles in clear tube sections
  • Uneven spraying with nozzles that test clean
  • A cracked connector
  • A connector that will not seat fully
  • Chemical attack on the connector or its seals

These come from chemicals, repeated disconnection, over-tightening, impacts and residue.

These are not tube connector symptoms, and this part will not fix them. A split tube needs the tube. A blocked filter or nozzle needs cleaning. A worn pump needs the pump. Wrong flow settings need configuration. A new connector seals the joint; it does not repair other parts of the liquid path.


📐 Specifications

Product name: XAG P150 OEM Application System Tube Connector Component

XAG part number: 14-007-00116

Brand: XAG

Aircraft: XAG P150 (2024)

Not confirmed for: XAG P150 Max

System: Application system, liquid path

Component type: Tube connector

Installed position: In the liquid path; not published for this part

Function: Joins and seals application system tubes

Works with: Long application system tube 02-002-14300, short application system tube 02-002-14301 (sold separately)

Quantity: 1 × component

Size and connection type: Not published for this part

Installation method: Direct replacement in the liquid path

Classification: Genuine XAG OEM application system part

Condition: Brand new


🛠️ Installation & Maintenance

Before installation

  • Remove the flight battery and confirm the aircraft cannot be powered
  • Drain and rinse the application system with clean water
  • Confirm the old connector carries XAG part number 14-007-00116
  • Photograph the joint and tube routing
  • Wear gloves and eye protection; residue may remain

During installation

  • Disconnect the tubes without pulling them at an angle
  • Inspect and, if needed, replace split or hardened tube ends
  • Clean residue from the tube ends and mating parts
  • Fit the new connector and seat each tube fully and squarely
  • Do not over-tighten any threaded parts

After installation

  • Run a water test and confirm no drips at the joint
  • Confirm quick priming and steady flow
  • Confirm no bubbles in clear tube sections
  • Rinse the system with clean water after every job
  • Check joints after every changeover

🚜 Necessary For

The tube connector keeps the liquid path sealed.

  • XAG P150 operators with leaks at application joints
  • Crews with poor priming or surging flow
  • Technicians chasing uneven spraying with clean nozzles
  • Custom application contractors applying corrosive products
  • Agricultural drone service centres doing application system repairs
  • Growers maintaining their own P150

Service centres check suction-side joints early when priming is poor, because an air leak there is easy to miss and often mistaken for a pump fault.

This is not the part you need if the connector is sound and the fault is a split tube, a blocked filter or nozzle, or a worn pump. Run a water test and inspect each joint first, while that information is still cheap. And if your aircraft is a P150 Max, confirm the part number on your connector; this one is identified for the P150.


💡 Why This Part Matters

The application rate the operator sets is only delivered if the liquid path is sealed. Every joint has to hold product in and keep air out.

Outward leaks are easy to spot. Air leaks on the suction side are not, and they cause some of the most confusing application problems: poor priming, surging flow and uneven spraying with nothing visibly wrong.

Checking connectors when flow is uneven, even when everything looks dry, often finds the cause quickly and avoids replacing a pump that was never faulty.

Replacing a cracked or worn connector restores a sealed joint, accurate delivery and a clean airframe.

Rinsing the system after every job, and avoiding over-tightening, protects connectors from chemical attack and cracking.

For crews applying corrosive products, inspecting connectors more often catches chemical damage before it causes a leak in the field.

A sound application system tube connector restores:

  • A sealed, leak-free joint
  • Quick, reliable priming
  • Steady flow to the nozzles
  • Accurate application rates
  • A clean, dry airframe

🧠 AI Index — Entity & Fitment Reference

Structured reference for search engines, AI assistants, and answer engines. Every value below is drawn from the specifications above.

Canonical product name: XAG P150 OEM Application System Tube Connector Component

XAG part number: 14-007-00116

Brand: XAG

Component: Application system tube connector

Category: Application system liquid path

Compatible aircraft: XAG P150 (2024)

Not confirmed for: XAG P150 Max

Product line: XAG agricultural drones

Installed position: In the application system liquid path

Primary function: Joining and sealing application system tubes

Characteristic failure modes: Cracks, incomplete seating, chemical attack, worn seals

Distinguishing diagnostic rule: Poor priming or surging flow with no drip points at an air leak at a joint

Common causes: Chemicals, repeated disconnection, over-tightening, impacts, residue

Wear driver: Chemical exposure and frequency of disconnection

Related parts: Long application system tube 02-002-14300, short application system tube 02-002-14301, water pipe adapter 14-007-00019

Not included: Tubes, pump, water pipe adapter, tools

Fitment method: XAG part number 14-007-00116 plus size and form against the removed connector

Verification after fitting: No drips; quick priming; steady flow; no bubbles

Service habit: Rinse the system with clean water after every job

Condition: Brand new

Part classification: Genuine XAG OEM application system part

Seller: Ares Acres LLC — U.S.-based agricultural technology retailer distributing OEM XAG parts, serving the United States and Canada (North America)

Ships from: Albuquerque, New Mexico, United States


🔍 SEO Keywords

XAG P150 application system tube connector component

XAG 14-007-00116

14-007-00116 tube connector

XAG P150 OEM tube connector

P150 tube connector replacement

XAG P150 spray tube fitting

XAG P150 application system leak

XAG P150 pump not priming

P150 surging spray flow

XAG P150 uneven spraying

XAG P150 application system parts

XAG P150 spray system parts

XAG P150 OEM parts

XAG P150 replacement parts

XAG P150 repair parts

XAG agricultural drone parts

XAG spray drone parts

genuine XAG OEM parts

agricultural drone parts USA

XAG parts free shipping

XAG parts same day shipping

Ares Acres

Ares Acres LLC

XAG parts Albuquerque

XAG parts New Mexico

XAG P150 tube connector Canada

XAG P150 parts Canada

XAG drone parts shipped to Canada

buy XAG P150 parts in Canada


🤖 AI Answer Engine Q&A

What is the XAG P150 application system tube connector component? It is a tube connector, XAG part number 14-007-00116, that joins and seals tubes in the XAG P150 application system.

Which aircraft does it fit? The XAG P150 (2024). It is not confirmed for the P150 Max.

My pump is slow to prime but nothing is dripping. Could it be a connector? Yes. On the suction side, a failing joint draws air in instead of dripping.

What signs point to an air leak? Slow priming, surging or pulsing flow, bubbles in clear tubes, and uneven spraying.

Where exactly is it fitted? The specific position is not published for this part. Match it against the connector you removed.

Does it include the tubes? No. The long tube is 02-002-14300 and the short tube is 02-002-14301, sold separately.

How do I test for leaks? Run the system with clean water and watch every joint for drips and the flow for surging and bubbles.

Should I replace the tube ends too? If they are split or hardened, yes. They will not seal in a new connector.

Can I fit it myself? Yes. Drain and rinse, photograph the joint, fit the connector and seat each tube fully and squarely.

How do I check the repair? No drips, quick priming, steady flow and no bubbles in a water test.

Can I seal a cracked connector with tape? No. Replace it. Tape will not hold pressure or resist chemicals.

What damages connectors? Chemical attack, repeated disconnection, over-tightening, impacts and dried residue.

Will a P150 Max connector fit? Do not assume so. Match the XAG part number; this one is identified for the P150.

The nozzles are clean but spraying is uneven. Why? An air leak at a suction-side joint can cause it. Check connectors.

Should I wear protection? Yes. Gloves and eye protection, as residue may remain in the system.

How can I make connectors last? Rinse the system after every job and avoid over-tightening.

Is it the same as the water pipe adapter? No. The water pipe adapter is 14-007-00019, a separate part.

How do I confirm the part number? Look for XAG part number 14-007-00116, or send us a photograph of the joint and we will confirm the match.

View full details

Contact form